Note: reverted back to basic kernel perameters because the previous kernel didn't have everything enabled. Will try now minus rotate:1 but have altered nothing else. xorg.conf for example.
Now from the line below it seems not accepting the edid. I do not know clearly,
- Code: Select all
zgrep -i edid /proc/config.gz
CONFIG_DRM_LOAD_EDID_FIRMWARE=y
CONFIG_FIRMWARE_EDID=y
- Code: Select all
xrandr --verbose
Screen 0: minimum 8 x 8, current 600 x 800, maximum 32767 x 32767
eDP1 connected primary 600x800+0+0 (0x1ca) right (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x43
Timestamp: 34671
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
BACKLIGHT: 480
range: (0, 480)
Backlight: 480
range: (0, 480)
scaling mode: Full aspect
supported: Full, Center, Full aspect
Colorspace: Default
supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
max bpc: 12
range: (6, 12)
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
link-status: Good
supported: Good, Bad
non-desktop: 0
range: (0, 1)
800x600 (0x1ca) 62.357MHz +HSync +VSync *current +preferred
h: width 800 start 821 end 901 total 1040 skew 0 clock 59.96KHz
v: height 600 start 601 end 604 total 632 clock 94.87Hz
1024x768 (0x1c1) 112.620MHz +HSync +VSync
h: width 1024 start 1076 end 1248 total 1420 skew 0 clock 79.31KHz
v: height 768 start 768 end 780 total 808 clock 98.16Hz
1024x768 (0x1c2) 78.525MHz +HSync +VSync
h: width 1024 start 1049 end 1145 total 1312 skew 0 clock 59.85KHz
v: height 768 start 769 end 772 total 800 clock 74.81Hz
1024x768 (0x1c3) 65.000MHz -HSync -VSync
h: width 1024 start 1032 end 1176 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
1024x768 (0x49) 65.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
1024x768i (0x1de) 44.900MHz +HSync +VSync Interlace
h: width 1024 start 1032 end 1208 total 1264 skew 0 clock 35.52KHz
v: height 768 start 768 end 776 total 817 clock 86.96Hz
1024x576 (0x1c4) 46.500MHz -HSync +VSync
h: width 1024 start 1064 end 1160 total 1296 skew 0 clock 35.88KHz
v: height 576 start 579 end 584 total 599 clock 59.90Hz
1024x576 (0x1c5) 42.000MHz +HSync -VSync
h: width 1024 start 1072 end 1104 total 1184 skew 0 clock 35.47KHz
v: height 576 start 579 end 584 total 593 clock 59.82Hz
832x624 (0x1df) 57.284MHz -HSync -VSync
h: width 832 start 864 end 928 total 1152 skew 0 clock 49.73KHz
v: height 624 start 625 end 628 total 667 clock 74.55Hz
832x624 (0x1c6) 57.000MHz -HSync -VSync
h: width 832 start 876 end 940 total 1152 skew 0 clock 49.48KHz
v: height 624 start 625 end 628 total 667 clock 74.18Hz
960x540 (0x1c7) 40.750MHz -HSync +VSync
h: width 960 start 992 end 1088 total 1216 skew 0 clock 33.51KHz
v: height 540 start 543 end 548 total 562 clock 59.63Hz
960x540 (0x1c8) 37.250MHz +HSync -VSync
h: width 960 start 1008 end 1040 total 1120 skew 0 clock 33.26KHz
v: height 540 start 543 end 548 total 556 clock 59.82Hz
800x600 (0x1c9) 100.000MHz -HSync -VSync
h: width 800 start 816 end 824 total 840 skew 0 clock 119.05KHz
v: height 600 start 616 end 624 total 640 clock 186.01Hz
800x600 (0x1ca) 62.357MHz +HSync +VSync *current
h: width 800 start 821 end 901 total 1040 skew 0 clock 59.96KHz
v: height 600 start 601 end 604 total 632 clock 94.87Hz
800x600 (0x1e0) 56.300MHz +HSync +VSync
h: width 800 start 832 end 896 total 1048 skew 0 clock 53.72KHz
v: height 600 start 601 end 604 total 631 clock 85.14Hz
800x600 (0x1e1) 50.000MHz +HSync +VSync
h: width 800 start 856 end 976 total 1040 skew 0 clock 48.08KHz
v: height 600 start 637 end 643 total 666 clock 72.19Hz
800x600 (0x1e2) 49.500MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.88KHz
v: height 600 start 601 end 604 total 625 clock 75.00Hz
800x600 (0x1cb) 40.000MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.88KHz
v: height 600 start 601 end 605 total 628 clock 60.32Hz
800x600 (0x1cc) 36.000MHz +HSync +VSync
h: width 800 start 824 end 896 total 1024 skew 0 clock 35.16KHz
v: height 600 start 601 end 603 total 625 clock 56.25Hz
768x576 (0x1cd) 63.070MHz
h: width 768 start 800 end 960 total 1024 skew 0 clock 61.59KHz
v: height 576 start 578 end 590 total 616 clock 99.99Hz
768x576 (0x1ce) 50.000MHz
h: width 768 start 832 end 846 total 1000 skew 0 clock 50.00KHz
v: height 576 start 590 end 595 total 630 clock 79.37Hz
864x486 (0x1cf) 32.500MHz -HSync +VSync
h: width 864 start 888 end 968 total 1072 skew 0 clock 30.32KHz
v: height 486 start 489 end 494 total 506 clock 59.92Hz
864x486 (0x1d0) 30.500MHz +HSync -VSync
h: width 864 start 912 end 944 total 1024 skew 0 clock 29.79KHz
v: height 486 start 489 end 494 total 500 clock 59.57Hz
848x480 (0x1d1) 33.750MHz +HSync +VSync
h: width 848 start 864 end 976 total 1088 skew 0 clock 31.02KHz
v: height 480 start 486 end 494 total 517 clock 60.00Hz
640x480 (0x1d2) 49.886MHz +HSync +VSync
h: width 640 start 661 end 725 total 832 skew 0 clock 59.96KHz
v: height 480 start 481 end 484 total 514 clock 116.65Hz
640x480 (0x1e3) 36.000MHz -HSync -VSync
h: width 640 start 696 end 752 total 832 skew 0 clock 43.27KHz
v: height 480 start 481 end 484 total 509 clock 85.01Hz
640x480 (0x1e4) 31.500MHz -HSync -VSync
h: width 640 start 664 end 704 total 832 skew 0 clock 37.86KHz
v: height 480 start 489 end 492 total 520 clock 72.81Hz
640x480 (0x1e5) 31.500MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.50KHz
v: height 480 start 481 end 484 total 500 clock 75.00Hz
640x480 (0x1d3) 25.175MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.47KHz
v: height 480 start 490 end 492 total 525 clock 59.94Hz
720x405 (0x1d4) 22.500MHz -HSync +VSync
h: width 720 start 744 end 808 total 896 skew 0 clock 25.11KHz
v: height 405 start 408 end 413 total 422 clock 59.51Hz
720x405 (0x1d5) 21.750MHz +HSync -VSync
h: width 720 start 768 end 800 total 880 skew 0 clock 24.72KHz
v: height 405 start 408 end 413 total 419 clock 58.99Hz
720x400 (0x1e6) 35.500MHz -HSync +VSync
h: width 720 start 756 end 828 total 936 skew 0 clock 37.93KHz
v: height 400 start 401 end 404 total 446 clock 85.04Hz
640x400 (0x1e7) 31.500MHz -HSync +VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.86KHz
v: height 400 start 401 end 404 total 445 clock 85.08Hz
640x360 (0x1d6) 18.000MHz -HSync +VSync
h: width 640 start 664 end 720 total 800 skew 0 clock 22.50KHz
v: height 360 start 363 end 368 total 376 clock 59.84Hz
640x360 (0x1d7) 17.750MHz +HSync -VSync
h: width 640 start 688 end 720 total 800 skew 0 clock 22.19KHz
v: height 360 start 363 end 368 total 374 clock 59.32Hz
640x350 (0x1e8) 31.500MHz +HSync -VSync
h: width 640 start 672 end 736 total 832 skew 0 clock 37.86KHz
v: height 350 start 382 end 385 total 445 clock 85.08Hz
400x300 (0x1e9) 14.963MHz -HSync +VSync
h: width 400 start 408 end 448 total 496 skew 0 clock 30.17KHz
v: height 300 start 301 end 304 total 318 clock 94.87Hz
DP1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x44
Timestamp: 34671
Subpixel: unknown
Clones:
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDCP Content Type: HDCP Type0
supported: HDCP Type0, HDCP Type1
Content Protection: Undesired
supported: Undesired, Desired, Enabled
Colorspace: Default
supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
max bpc: 12
range: (6, 12)
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
non-desktop: 0
range: (0, 1)
DP2 disconnected (normal left inverted right x axis y axis)
Identifier: 0x45
Timestamp: 34671
Subpixel: unknown
Clones:
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDCP Content Type: HDCP Type0
supported: HDCP Type0, HDCP Type1
Content Protection: Undesired
supported: Undesired, Desired, Enabled
Colorspace: Default
supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
max bpc: 12
range: (6, 12)
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
non-desktop: 0
range: (0, 1)
HDMI1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x46
Timestamp: 34671
Subpixel: unknown
Clones:
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
HDCP Content Type: HDCP Type0
supported: HDCP Type0, HDCP Type1
Content Protection: Undesired
supported: Undesired, Desired, Enabled
max bpc: 12
range: (8, 12)
content type: No Data
supported: No Data, Graphics, Photo, Cinema, Game
Colorspace: Default
supported: Default, SMPTE_170M_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, opRGB, BT2020_CYCC, BT2020_RGB, BT2020_YCC, DCI-P3_RGB_D65, DCI-P3_RGB_Theater
aspect ratio: Automatic
supported: Automatic, 4:3, 16:9
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
non-desktop: 0
range: (0, 1)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x47
Timestamp: 34671
Subpixel: no subpixels
Clones:
CRTCs: 3
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
non-desktop: 0
supported: 0, 1
- Code: Select all
journalctl -ab|grep -i edid
Sep 13 15:34:19 introvertx95.extrovertdomain kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 13 15:34:19 introvertx95.extrovertdomain kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 13 15:35:16 introvertx95.extrovertdomain colord[5653]: failed to get edid data: EDID length is too small
Edid length is too small?
/var/log/Xorg.0.log
- Code: Select all
[ 18.340] (--) Log file renamed from "/var/log/Xorg.pid-2858.log" to "/var/log/Xorg.0.log"
[ 18.345]
X.Org X Server 1.20.9
X Protocol Version 11, Revision 0
[ 18.345] Build Operating System: rabbit 5.6.8-server-1.mga7
[ 18.345] Current Operating System: Linux introvertx95.extrovertdomain 5.8.8-1.mga8custom #2 SMP Sun Sep 13 12:53:32 JST 2020 x86_64
[ 18.345] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
[ 18.345] Build Date: 26 August 2020 07:12:27AM
[ 18.345] Build ID: x11-server 1.20.9-7.mga8
[ 18.345] Current version of pixman: 0.40.0
[ 18.345] Before reporting problems, check https://bugs.mageia.org
to make sure that you have the latest version.
[ 18.345] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 18.345] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep 13 15:34:30 2020
[ 18.358] (==) Using config file: "/etc/X11/xorg.conf"
[ 18.358] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 18.358] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 18.368] (==) ServerLayout "layout1"
[ 18.368] (**) |-->Screen "screen1" (0)
[ 18.368] (**) | |-->Monitor "monitor1"
[ 18.368] (**) | |-->Device "device1"
[ 18.368] (**) Option "DontZap" "False"
[ 18.368] (**) Option "AllowMouseOpenFail"
[ 18.368] (==) Automatically adding devices
[ 18.368] (==) Automatically enabling devices
[ 18.368] (==) Automatically adding GPU devices
[ 18.368] (==) Automatically binding GPU devices
[ 18.368] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 18.368] (==) FontPath set to:
catalogue:/etc/X11/fontpath.d,
built-ins
[ 18.368] (**) ModulePath set to "/usr/lib64/xorg/extra-modules,/usr/lib64/xorg/modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 18.368] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 18.368] (II) Loader magic: 0x61fd40
[ 18.368] (II) Module ABI versions:
[ 18.368] X.Org ANSI C Emulation: 0.4
[ 18.368] X.Org Video Driver: 24.1
[ 18.368] X.Org XInput driver : 24.1
[ 18.368] X.Org Server Extension : 10.0
[ 18.369] (++) using VT number 1
[ 18.369] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 18.369] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 18.369] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card0
[ 18.380] (--) PCI:*(0@0:2:0) 8086:8a52:8086:2212 rev 7, Mem @ 0x601c000000/16777216, 0x4000000000/268435456, I/O @ 0x00004000/64, BIOS @ 0x????????/131072
[ 18.380] (II) Open ACPI successful (/var/run/acpid.socket)
[ 18.380] (II) "glx" will be loaded by default.
[ 18.380] (II) LoadModule: "v4l"
[ 18.380] (II) Loading /usr/lib64/xorg/modules/drivers/v4l_drv.so
[ 18.380] (II) Module v4l: vendor="X.Org Foundation"
[ 18.380] compiled for 1.20.7, module version = 0.1.1
[ 18.380] ABI class: X.Org Video Driver, version 24.1
[ 18.380] (II) LoadModule: "glx"
[ 18.380] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so
[ 18.381] (II) Module glx: vendor="X.Org Foundation"
[ 18.381] compiled for 1.20.9, module version = 1.0.0
[ 18.381] ABI class: X.Org Server Extension, version 10.0
[ 18.381] (II) LoadModule: "intel"
[ 18.381] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so
[ 18.387] (II) Module intel: vendor="X.Org Foundation"
[ 18.387] compiled for 1.20.8, module version = 2.99.917
[ 18.387] Module class: X.Org Video Driver
[ 18.387] ABI class: X.Org Video Driver, version 24.1
[ 18.387] (II) v4l driver for Video4Linux overlay mode (V4L2)
[ 18.388] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 18.388] (II) intel: Driver for Intel(R) HD Graphics
[ 18.388] (II) intel: Driver for Intel(R) Iris(TM) Graphics
[ 18.388] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics
[ 18.388] (WW) Falling back to old probe method for v4l
[ 18.388] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20200515
[ 18.400] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[ 18.400] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2; using a maximum of 4 threads
[ 18.400] (II) intel(0): Creating default Display subsection in Screen section
"screen1" for depth/fbbpp 24/32
[ 18.400] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 18.400] (==) intel(0): RGB weight 888
[ 18.400] (==) intel(0): Default visual is TrueColor
[ 18.400] (II) intel(0): Output eDP1 using monitor section monitor1
[ 18.401] (**) intel(0): Found backlight control interface intel_backlight (type 'raw') for output eDP1
[ 18.401] (II) intel(0): Enabled output eDP1
[ 18.401] (II) intel(0): Output HDMI1 has no monitor section
[ 18.401] (II) intel(0): Enabled output HDMI1
[ 18.401] (II) intel(0): Output DP1 has no monitor section
[ 18.401] (II) intel(0): Enabled output DP1
[ 18.401] (II) intel(0): Output DP2 has no monitor section
[ 18.401] (II) intel(0): Enabled output DP2
[ 18.401] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[ 18.401] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 18.401] (II) intel(0): Enabled output VIRTUAL1
[ 18.401] (--) intel(0): Output eDP1 using initial mode 1024x768 on pipe 0
[ 18.411] (==) intel(0): TearFree enabled
[ 18.411] (==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
[ 18.411] (==) intel(0): DPI set to (96, 96)
[ 18.411] (II) Loading sub module "dri3"
[ 18.411] (II) LoadModule: "dri3"
[ 18.411] (II) Module "dri3" already built-in
[ 18.411] (II) Loading sub module "dri2"
[ 18.411] (II) LoadModule: "dri2"
[ 18.411] (II) Module "dri2" already built-in
[ 18.411] (II) Loading sub module "present"
[ 18.411] (II) LoadModule: "present"
[ 18.411] (II) Module "present" already built-in
[ 18.435] (II) intel(0): SNA initialized with Skylake (gen9) backend
[ 18.435] (==) intel(0): Backing store enabled
[ 18.435] (==) intel(0): Silken mouse enabled
[ 18.440] (II) intel(0): HW Cursor enabled
[ 18.440] (**) intel(0): DPMS enabled
[ 18.440] (==) intel(0): Display hotplug detection enabled
[ 18.440] (II) intel(0): [DRI2] Setup complete
[ 18.440] (II) intel(0): [DRI2] DRI driver: i965
[ 18.440] (II) intel(0): [DRI2] VDPAU driver: va_gl
[ 18.440] (II) intel(0): direct rendering: DRI2 DRI3 enabled
[ 18.440] (II) intel(0): hardware support for Present enabled
[ 18.440] (II) Initializing extension Generic Event Extension
[ 18.440] (II) Initializing extension SHAPE
[ 18.440] (II) Initializing extension MIT-SHM
[ 18.440] (II) Initializing extension XInputExtension
[ 18.443] (II) Initializing extension XTEST
[ 18.443] (II) Initializing extension BIG-REQUESTS
[ 18.443] (II) Initializing extension SYNC
[ 18.443] (II) Initializing extension XKEYBOARD
[ 18.443] (II) Initializing extension XC-MISC
[ 18.443] (II) Initializing extension SECURITY
[ 18.444] (II) Initializing extension XFIXES
[ 18.444] (II) Initializing extension RENDER
[ 18.444] (II) Initializing extension RANDR
[ 18.444] (II) Initializing extension COMPOSITE
[ 18.444] (II) Initializing extension DAMAGE
[ 18.444] (II) Initializing extension MIT-SCREEN-SAVER
[ 18.444] (II) Initializing extension DOUBLE-BUFFER
[ 18.444] (II) Initializing extension RECORD
[ 18.444] (II) Initializing extension DPMS
[ 18.444] (II) Initializing extension Present
[ 18.444] (II) Initializing extension DRI3
[ 18.444] (II) Initializing extension X-Resource
[ 18.444] (II) Initializing extension XVideo
[ 18.445] (II) Initializing extension XVideo-MotionCompensation
[ 18.445] (II) Initializing extension GLX
[ 18.589] (II) AIGLX: Loaded and initialized i965
[ 18.589] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 18.589] (II) Initializing extension XFree86-VidModeExtension
[ 18.589] (II) Initializing extension XFree86-DGA
[ 18.589] (II) Initializing extension XFree86-DRI
[ 18.591] (II) Initializing extension DRI2
[ 18.593] (II) intel(0): switch to mode 1024x768@60.0 on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 18.595] (II) intel(0): Setting screen physical size to 270 x 203
[ 18.768] (II) config/udev: Adding input device Power Button (/dev/input/event11)
[ 18.768] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 18.768] (**) Power Button: Applying InputClass "system-keyboard"
[ 18.768] (II) LoadModule: "libinput"
[ 18.768] (II) Loading /usr/lib64/xorg/modules/input/libinput_drv.so
[ 18.769] (II) Module libinput: vendor="X.Org Foundation"
[ 18.769] compiled for 1.20.8, module version = 0.30.0
[ 18.769] Module class: X.Org XInput Driver
[ 18.769] ABI class: X.Org XInput driver, version 24.1
[ 18.769] (II) Using input driver 'libinput' for 'Power Button'
[ 18.769] (**) Power Button: always reports core events
[ 18.769] (**) Option "Device" "/dev/input/event11"
[ 18.769] (**) Option "_source" "server/udev"
[ 18.800] (II) event11 - Power Button: is tagged by udev as: Keyboard
[ 18.800] (II) event11 - Power Button: device is a keyboard
[ 18.800] (II) event11 - Power Button: device removed
[ 18.808] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input11/event11"
[ 18.808] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 18.808] (**) Option "xkb_model" "pc105"
[ 18.808] (**) Option "xkb_layout" "us"
[ 18.808] (**) Option "xkb_options" "compose:rwin"
[ 18.821] (II) event11 - Power Button: is tagged by udev as: Keyboard
[ 18.821] (II) event11 - Power Button: device is a keyboard
[ 18.821] (II) config/udev: Adding input device Video Bus (/dev/input/event1)
[ 18.821] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 18.821] (**) Video Bus: Applying InputClass "system-keyboard"
[ 18.821] (II) Using input driver 'libinput' for 'Video Bus'
[ 18.821] (**) Video Bus: always reports core events
[ 18.821] (**) Option "Device" "/dev/input/event1"
[ 18.821] (**) Option "_source" "server/udev"
[ 18.822] (II) event1 - Video Bus: is tagged by udev as: Keyboard
[ 18.822] (II) event1 - Video Bus: device is a keyboard
[ 18.822] (II) event1 - Video Bus: device removed
[ 18.834] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input1/event1"
[ 18.834] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 18.834] (**) Option "xkb_model" "pc105"
[ 18.834] (**) Option "xkb_layout" "us"
[ 18.834] (**) Option "xkb_options" "compose:rwin"
[ 18.834] (II) event1 - Video Bus: is tagged by udev as: Keyboard
[ 18.834] (II) event1 - Video Bus: device is a keyboard
[ 18.835] (II) config/udev: Adding input device Lid Switch (/dev/input/event8)
[ 18.835] (II) No input driver specified, ignoring this device.
[ 18.835] (II) This device may have been added with another device file.
[ 18.835] (II) config/udev: Adding input device Power Button (/dev/input/event10)
[ 18.835] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 18.835] (**) Power Button: Applying InputClass "system-keyboard"
[ 18.835] (II) Using input driver 'libinput' for 'Power Button'
[ 18.835] (**) Power Button: always reports core events
[ 18.835] (**) Option "Device" "/dev/input/event10"
[ 18.835] (**) Option "_source" "server/udev"
[ 18.835] (II) event10 - Power Button: is tagged by udev as: Keyboard
[ 18.835] (II) event10 - Power Button: device is a keyboard
[ 18.835] (II) event10 - Power Button: device removed
[ 18.843] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input10/event10"
[ 18.843] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 18.843] (**) Option "xkb_model" "pc105"
[ 18.843] (**) Option "xkb_layout" "us"
[ 18.843] (**) Option "xkb_options" "compose:rwin"
[ 18.843] (II) event10 - Power Button: is tagged by udev as: Keyboard
[ 18.844] (II) event10 - Power Button: device is a keyboard
[ 18.844] (II) config/udev: Adding input device Sleep Button (/dev/input/event9)
[ 18.844] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[ 18.844] (**) Sleep Button: Applying InputClass "system-keyboard"
[ 18.844] (II) Using input driver 'libinput' for 'Sleep Button'
[ 18.844] (**) Sleep Button: always reports core events
[ 18.844] (**) Option "Device" "/dev/input/event9"
[ 18.844] (**) Option "_source" "server/udev"
[ 18.845] (II) event9 - Sleep Button: is tagged by udev as: Keyboard
[ 18.845] (II) event9 - Sleep Button: device is a keyboard
[ 18.845] (II) event9 - Sleep Button: device removed
[ 18.854] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input9/event9"
[ 18.854] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 18.854] (**) Option "xkb_model" "pc105"
[ 18.854] (**) Option "xkb_layout" "us"
[ 18.854] (**) Option "xkb_options" "compose:rwin"
[ 18.854] (II) event9 - Sleep Button: is tagged by udev as: Keyboard
[ 18.854] (II) event9 - Sleep Button: device is a keyboard
[ 18.855] (II) config/udev: Adding input device HID 6901:2701 (/dev/input/event2)
[ 18.855] (**) HID 6901:2701: Applying InputClass "libinput keyboard catchall"
[ 18.855] (**) HID 6901:2701: Applying InputClass "system-keyboard"
[ 18.855] (II) Using input driver 'libinput' for 'HID 6901:2701'
[ 18.855] (**) HID 6901:2701: always reports core events
[ 18.855] (**) Option "Device" "/dev/input/event2"
[ 18.855] (**) Option "_source" "server/udev"
[ 18.856] (II) event2 - HID 6901:2701: is tagged by udev as: Keyboard
[ 18.856] (II) event2 - HID 6901:2701: device is a keyboard
[ 18.856] (II) event2 - HID 6901:2701: device removed
[ 18.870] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.0/0003:6901:2701.0001/input/input2/event2"
[ 18.870] (II) XINPUT: Adding extended input device "HID 6901:2701" (type: KEYBOARD, id 10)
[ 18.870] (**) Option "xkb_model" "pc105"
[ 18.870] (**) Option "xkb_layout" "us"
[ 18.870] (**) Option "xkb_options" "compose:rwin"
[ 18.871] (II) event2 - HID 6901:2701: is tagged by udev as: Keyboard
[ 18.871] (II) event2 - HID 6901:2701: device is a keyboard
[ 18.872] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/event3)
[ 18.872] (**) HID 6901:2701 Mouse: Applying InputClass "libinput pointer catchall"
[ 18.872] (II) Using input driver 'libinput' for 'HID 6901:2701 Mouse'
[ 18.872] (**) HID 6901:2701 Mouse: always reports core events
[ 18.872] (**) Option "Device" "/dev/input/event3"
[ 18.872] (**) Option "_source" "server/udev"
[ 18.873] (II) event3 - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[ 18.873] (II) event3 - HID 6901:2701 Mouse: device is a pointer
[ 18.873] (II) event3 - HID 6901:2701 Mouse: device removed
[ 18.884] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input3/event3"
[ 18.884] (II) XINPUT: Adding extended input device "HID 6901:2701 Mouse" (type: MOUSE, id 11)
[ 18.884] (**) Option "AccelerationScheme" "none"
[ 18.884] (**) HID 6901:2701 Mouse: (accel) selected scheme none/0
[ 18.884] (**) HID 6901:2701 Mouse: (accel) acceleration factor: 2.000
[ 18.884] (**) HID 6901:2701 Mouse: (accel) acceleration threshold: 4
[ 18.886] (II) event3 - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[ 18.886] (II) event3 - HID 6901:2701 Mouse: device is a pointer
[ 18.887] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/mouse0)
[ 18.887] (II) No input driver specified, ignoring this device.
[ 18.887] (II) This device may have been added with another device file.
[ 18.887] (II) config/udev: Adding input device HID 6901:2701 Consumer Control (/dev/input/event4)
[ 18.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 18.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[ 18.888] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[ 18.888] (**) HID 6901:2701 Consumer Control: always reports core events
[ 18.888] (**) Option "Device" "/dev/input/event4"
[ 18.888] (**) Option "_source" "server/udev"
[ 18.889] (II) event4 - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[ 18.889] (II) event4 - HID 6901:2701 Consumer Control: device is a keyboard
[ 18.889] (II) event4 - HID 6901:2701 Consumer Control: device removed
[ 18.897] (II) libinput: HID 6901:2701 Consumer Control: needs a virtual subdevice
[ 18.897] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[ 18.897] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: MOUSE, id 12)
[ 18.897] (**) Option "AccelerationScheme" "none"
[ 18.897] (**) HID 6901:2701 Consumer Control: (accel) selected scheme none/0
[ 18.897] (**) HID 6901:2701 Consumer Control: (accel) acceleration factor: 2.000
[ 18.897] (**) HID 6901:2701 Consumer Control: (accel) acceleration threshold: 4
[ 18.898] (II) event4 - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[ 18.898] (II) event4 - HID 6901:2701 Consumer Control: device is a keyboard
[ 18.899] (II) config/udev: Adding input device HID 6901:2701 System Control (/dev/input/event5)
[ 18.899] (**) HID 6901:2701 System Control: Applying InputClass "libinput keyboard catchall"
[ 18.899] (**) HID 6901:2701 System Control: Applying InputClass "system-keyboard"
[ 18.899] (II) Using input driver 'libinput' for 'HID 6901:2701 System Control'
[ 18.899] (**) HID 6901:2701 System Control: always reports core events
[ 18.899] (**) Option "Device" "/dev/input/event5"
[ 18.899] (**) Option "_source" "server/udev"
[ 18.900] (II) event5 - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[ 18.900] (II) event5 - HID 6901:2701 System Control: device is a keyboard
[ 18.900] (II) event5 - HID 6901:2701 System Control: device removed
[ 18.910] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input5/event5"
[ 18.910] (II) XINPUT: Adding extended input device "HID 6901:2701 System Control" (type: KEYBOARD, id 13)
[ 18.910] (**) Option "xkb_model" "pc105"
[ 18.910] (**) Option "xkb_layout" "us"
[ 18.910] (**) Option "xkb_options" "compose:rwin"
[ 18.911] (II) event5 - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[ 18.911] (II) event5 - HID 6901:2701 System Control: device is a keyboard
[ 18.911] (II) config/udev: Adding input device Mouse for Windows (/dev/input/event6)
[ 18.911] (**) Mouse for Windows: Applying InputClass "libinput pointer catchall"
[ 18.911] (II) Using input driver 'libinput' for ' Mouse for Windows'
[ 18.911] (**) Mouse for Windows: always reports core events
[ 18.911] (**) Option "Device" "/dev/input/event6"
[ 18.911] (**) Option "_source" "server/udev"
[ 18.963] (II) event6 - Mouse for Windows: is tagged by udev as: Mouse
[ 18.963] (II) event6 - Mouse for Windows: device is a pointer
[ 18.963] (II) event6 - Mouse for Windows: device removed
[ 18.976] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.0/0003:2F24:0118.0003/input/input6/event6"
[ 18.976] (II) XINPUT: Adding extended input device " Mouse for Windows" (type: MOUSE, id 14)
[ 18.976] (**) Option "AccelerationScheme" "none"
[ 18.976] (**) Mouse for Windows: (accel) selected scheme none/0
[ 18.976] (**) Mouse for Windows: (accel) acceleration factor: 2.000
[ 18.976] (**) Mouse for Windows: (accel) acceleration threshold: 4
[ 19.033] (II) event6 - Mouse for Windows: is tagged by udev as: Mouse
[ 19.033] (II) event6 - Mouse for Windows: device is a pointer
[ 19.036] (II) config/udev: Adding input device Mouse for Windows (/dev/input/mouse1)
[ 19.036] (II) No input driver specified, ignoring this device.
[ 19.037] (II) This device may have been added with another device file.
[ 19.039] (II) config/udev: Adding input device Mouse for Windows (/dev/input/event7)
[ 19.039] (**) Mouse for Windows: Applying InputClass "libinput keyboard catchall"
[ 19.039] (**) Mouse for Windows: Applying InputClass "system-keyboard"
[ 19.039] (II) Using input driver 'libinput' for ' Mouse for Windows'
[ 19.039] (**) Mouse for Windows: always reports core events
[ 19.039] (**) Option "Device" "/dev/input/event7"
[ 19.039] (**) Option "_source" "server/udev"
[ 19.045] (II) event7 - Mouse for Windows: is tagged by udev as: Keyboard
[ 19.045] (II) event7 - Mouse for Windows: device is a keyboard
[ 19.046] (II) event7 - Mouse for Windows: device removed
[ 19.059] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.1/0003:2F24:0118.0004/input/input7/event7"
[ 19.059] (II) XINPUT: Adding extended input device " Mouse for Windows" (type: KEYBOARD, id 15)
[ 19.059] (**) Option "xkb_model" "pc105"
[ 19.059] (**) Option "xkb_layout" "us"
[ 19.059] (**) Option "xkb_options" "compose:rwin"
[ 19.065] (II) event7 - Mouse for Windows: is tagged by udev as: Keyboard
[ 19.066] (II) event7 - Mouse for Windows: device is a keyboard
[ 19.068] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/event14)
[ 19.068] (**) HTIX5288:00 093A:0255 Mouse: Applying InputClass "libinput pointer catchall"
[ 19.068] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Mouse'
[ 19.068] (**) HTIX5288:00 093A:0255 Mouse: always reports core events
[ 19.068] (**) Option "Device" "/dev/input/event14"
[ 19.068] (**) Option "_source" "server/udev"
[ 19.071] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[ 19.072] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[ 19.074] (II) event14 - HTIX5288:00 093A:0255 Mouse: device removed
[ 19.091] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input17/event14"
[ 19.091] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Mouse" (type: MOUSE, id 16)
[ 19.091] (**) Option "AccelerationScheme" "none"
[ 19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) selected scheme none/0
[ 19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration factor: 2.000
[ 19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration threshold: 4
[ 19.097] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[ 19.098] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[ 19.102] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/mouse2)
[ 19.102] (II) No input driver specified, ignoring this device.
[ 19.102] (II) This device may have been added with another device file.
[ 19.103] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/event15)
[ 19.103] (**) HTIX5288:00 093A:0255 Touchpad: Applying InputClass "libinput touchpad catchall"
[ 19.103] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Touchpad'
[ 19.103] (**) HTIX5288:00 093A:0255 Touchpad: always reports core events
[ 19.103] (**) Option "Device" "/dev/input/event15"
[ 19.103] (**) Option "_source" "server/udev"
[ 19.106] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[ 19.106] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[ 19.107] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[ 19.107] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device removed
[ 19.127] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input18/event15"
[ 19.127] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Touchpad" (type: TOUCHPAD, id 17)
[ 19.127] (**) Option "AccelerationScheme" "none"
[ 19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) selected scheme none/0
[ 19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration factor: 2.000
[ 19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration threshold: 4
[ 19.128] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[ 19.128] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[ 19.129] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[ 19.129] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/mouse3)
[ 19.129] (II) No input driver specified, ignoring this device.
[ 19.129] (II) This device may have been added with another device file.
[ 19.129] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/event16)
[ 19.129] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[ 19.130] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[ 19.130] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[ 19.130] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[ 19.130] (**) Goodix Capacitive TouchScreen: always reports core events
[ 19.130] (**) Option "Device" "/dev/input/event16"
[ 19.130] (**) Option "_source" "server/udev"
[ 19.130] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[ 19.130] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[ 19.130] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[ 19.130] (II) event16 - Goodix Capacitive TouchScreen: device removed
[ 19.147] (II) libinput: Goodix Capacitive TouchScreen: needs a virtual subdevice
[ 19.147] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[ 19.147] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: TOUCHSCREEN, id 18)
[ 19.147] (**) Option "AccelerationScheme" "none"
[ 19.147] (**) Goodix Capacitive TouchScreen: (accel) selected scheme none/0
[ 19.147] (**) Goodix Capacitive TouchScreen: (accel) acceleration factor: 2.000
[ 19.147] (**) Goodix Capacitive TouchScreen: (accel) acceleration threshold: 4
[ 19.147] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[ 19.147] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[ 19.147] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[ 19.148] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/mouse4)
[ 19.148] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[ 19.148] (II) No input driver specified, ignoring this device.
[ 19.148] (II) This device may have been added with another device file.
[ 19.148] (II) config/udev: Adding input device Intel HID events (/dev/input/event12)
[ 19.148] (**) Intel HID events: Applying InputClass "libinput keyboard catchall"
[ 19.148] (**) Intel HID events: Applying InputClass "system-keyboard"
[ 19.148] (II) Using input driver 'libinput' for 'Intel HID events'
[ 19.148] (**) Intel HID events: always reports core events
[ 19.148] (**) Option "Device" "/dev/input/event12"
[ 19.148] (**) Option "_source" "server/udev"
[ 19.149] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[ 19.149] (II) event12 - Intel HID events: device is a keyboard
[ 19.149] (II) event12 - Intel HID events: device removed
[ 19.159] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input12/event12"
[ 19.159] (II) XINPUT: Adding extended input device "Intel HID events" (type: KEYBOARD, id 19)
[ 19.159] (**) Option "xkb_model" "pc105"
[ 19.159] (**) Option "xkb_layout" "us"
[ 19.159] (**) Option "xkb_options" "compose:rwin"
[ 19.159] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[ 19.159] (II) event12 - Intel HID events: device is a keyboard
[ 19.160] (II) config/udev: Adding input device Intel HID 5 button array (/dev/input/event13)
[ 19.160] (**) Intel HID 5 button array: Applying InputClass "libinput keyboard catchall"
[ 19.160] (**) Intel HID 5 button array: Applying InputClass "system-keyboard"
[ 19.160] (II) Using input driver 'libinput' for 'Intel HID 5 button array'
[ 19.160] (**) Intel HID 5 button array: always reports core events
[ 19.160] (**) Option "Device" "/dev/input/event13"
[ 19.160] (**) Option "_source" "server/udev"
[ 19.160] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[ 19.160] (II) event13 - Intel HID 5 button array: device is a keyboard
[ 19.160] (II) event13 - Intel HID 5 button array: device removed
[ 19.171] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input13/event13"
[ 19.171] (II) XINPUT: Adding extended input device "Intel HID 5 button array" (type: KEYBOARD, id 20)
[ 19.171] (**) Option "xkb_model" "pc105"
[ 19.171] (**) Option "xkb_layout" "us"
[ 19.171] (**) Option "xkb_options" "compose:rwin"
[ 19.171] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[ 19.171] (II) event13 - Intel HID 5 button array: device is a keyboard
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event17)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event18)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event19)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event20)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event21)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event22)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=10 (/dev/input/event23)
[ 19.172] (II) No input driver specified, ignoring this device.
[ 19.172] (II) This device may have been added with another device file.
[ 19.173] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=11 (/dev/input/event24)
[ 19.173] (II) No input driver specified, ignoring this device.
[ 19.173] (II) This device may have been added with another device file.
[ 19.173] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=12 (/dev/input/event25)
[ 19.173] (II) No input driver specified, ignoring this device.
[ 19.173] (II) This device may have been added with another device file.
[ 19.173] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 19.173] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[ 19.173] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[ 19.173] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[ 19.173] (**) AT Translated Set 2 keyboard: always reports core events
[ 19.173] (**) Option "Device" "/dev/input/event0"
[ 19.173] (**) Option "_source" "server/udev"
[ 19.174] (II) event0 - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[ 19.174] (II) event0 - AT Translated Set 2 keyboard: device is a keyboard
[ 19.174] (II) event0 - AT Translated Set 2 keyboard: device removed
[ 19.183] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 19.183] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 21)
[ 19.183] (**) Option "xkb_model" "pc105"
[ 19.183] (**) Option "xkb_layout" "us"
[ 19.183] (**) Option "xkb_options" "compose:rwin"
[ 19.183] (II) event0 - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[ 19.183] (II) event0 - AT Translated Set 2 keyboard: device is a keyboard
[ 19.212] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 19.212] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[ 19.212] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[ 19.212] (**) HID 6901:2701 Consumer Control: always reports core events
[ 19.212] (**) Option "Device" "/dev/input/event4"
[ 19.212] (**) Option "_source" "_driver/libinput"
[ 19.212] (II) libinput: HID 6901:2701 Consumer Control: is a virtual subdevice
[ 19.212] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[ 19.212] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: KEYBOARD, id 22)
[ 19.212] (**) Option "xkb_model" "pc105"
[ 19.212] (**) Option "xkb_layout" "us"
[ 19.212] (**) Option "xkb_options" "compose:rwin"
[ 19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[ 19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[ 19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[ 19.212] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[ 19.212] (**) Goodix Capacitive TouchScreen: always reports core events
[ 19.212] (**) Option "Device" "/dev/input/event16"
[ 19.212] (**) Option "_source" "_driver/libinput"
[ 19.212] (II) libinput: Goodix Capacitive TouchScreen: is a virtual subdevice
[ 19.212] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[ 19.212] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: KEYBOARD, id 23)
[ 19.212] (**) Option "xkb_model" "pc105"
[ 19.212] (**) Option "xkb_layout" "us"
[ 19.212] (**) Option "xkb_options" "compose:rwin"
[ 19.217] (EE) Failed to open authorization file "/var/run/sddm/{ef2571fe-2c16-47ce-bab6-adb31b0af8ba}": No such file or directory
[ 34.669] (II) intel(0): resizing framebuffer to 600x800
[ 34.671] (II) intel(0): switch to mode 800x600@94.9 on eDP1 using pipe 0, position (0, 0), rotation right, reflection none
[ 99.625] (EE) intel(0): Failed to submit rendering commands (Input/output error), disabling acceleration.
[ 99.625] (EE) intel(0): When reporting this, please include /sys/class/drm/card0/error and the full dmesg.