Mageia on GPD Win Max, can it?

This forum is dedicated to basic help and support :

Ask here your questions about basic installation and usage of Mageia. For example you may post here all your questions about getting Mageia isos and installing it, configuring your printer, using your word processor etc.

Try to ask your questions in the right sub-forum with as much details as you can gather. the more precise the question will be, the more likely you are to get a useful answer

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 13th, '20, 08:58

Currently:
Note: reverted back to basic kernel perameters because the previous kernel didn't have everything enabled. Will try now minus rotate:1 but have altered nothing else. xorg.conf for example.

Now from the line below it seems not accepting the edid. I do not know clearly,


Code: Select all
zgrep -i edid /proc/config.gz
CONFIG_DRM_LOAD_EDID_FIRMWARE=y
CONFIG_FIRMWARE_EDID=y


Code: Select all
xrandr --verbose
Screen 0: minimum 8 x 8, current 600 x 800, maximum 32767 x 32767
eDP1 connected primary 600x800+0+0 (0x1ca) right (normal left inverted right x axis y axis) 0mm x 0mm
   Identifier: 0x43
   Timestamp:  34671
   Subpixel:   unknown
   Gamma:      1.0:1.0:1.0
   Brightness: 1.0
   Clones:   
   CRTC:       0
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   BACKLIGHT: 480
      range: (0, 480)
   Backlight: 480
      range: (0, 480)
   scaling mode: Full aspect
      supported: Full, Center, Full aspect
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
  800x600 (0x1ca) 62.357MHz +HSync +VSync *current +preferred
        h: width   800 start  821 end  901 total 1040 skew    0 clock  59.96KHz
        v: height  600 start  601 end  604 total  632           clock  94.87Hz
  1024x768 (0x1c1) 112.620MHz +HSync +VSync
        h: width  1024 start 1076 end 1248 total 1420 skew    0 clock  79.31KHz
        v: height  768 start  768 end  780 total  808           clock  98.16Hz
  1024x768 (0x1c2) 78.525MHz +HSync +VSync
        h: width  1024 start 1049 end 1145 total 1312 skew    0 clock  59.85KHz
        v: height  768 start  769 end  772 total  800           clock  74.81Hz
  1024x768 (0x1c3) 65.000MHz -HSync -VSync
        h: width  1024 start 1032 end 1176 total 1344 skew    0 clock  48.36KHz
        v: height  768 start  771 end  777 total  806           clock  60.00Hz
  1024x768 (0x49) 65.000MHz -HSync -VSync
        h: width  1024 start 1048 end 1184 total 1344 skew    0 clock  48.36KHz
        v: height  768 start  771 end  777 total  806           clock  60.00Hz
  1024x768i (0x1de) 44.900MHz +HSync +VSync Interlace
        h: width  1024 start 1032 end 1208 total 1264 skew    0 clock  35.52KHz
        v: height  768 start  768 end  776 total  817           clock  86.96Hz
  1024x576 (0x1c4) 46.500MHz -HSync +VSync
        h: width  1024 start 1064 end 1160 total 1296 skew    0 clock  35.88KHz
        v: height  576 start  579 end  584 total  599           clock  59.90Hz
  1024x576 (0x1c5) 42.000MHz +HSync -VSync
        h: width  1024 start 1072 end 1104 total 1184 skew    0 clock  35.47KHz
        v: height  576 start  579 end  584 total  593           clock  59.82Hz
  832x624 (0x1df) 57.284MHz -HSync -VSync
        h: width   832 start  864 end  928 total 1152 skew    0 clock  49.73KHz
        v: height  624 start  625 end  628 total  667           clock  74.55Hz
  832x624 (0x1c6) 57.000MHz -HSync -VSync
        h: width   832 start  876 end  940 total 1152 skew    0 clock  49.48KHz
        v: height  624 start  625 end  628 total  667           clock  74.18Hz
  960x540 (0x1c7) 40.750MHz -HSync +VSync
        h: width   960 start  992 end 1088 total 1216 skew    0 clock  33.51KHz
        v: height  540 start  543 end  548 total  562           clock  59.63Hz
  960x540 (0x1c8) 37.250MHz +HSync -VSync
        h: width   960 start 1008 end 1040 total 1120 skew    0 clock  33.26KHz
        v: height  540 start  543 end  548 total  556           clock  59.82Hz
  800x600 (0x1c9) 100.000MHz -HSync -VSync
        h: width   800 start  816 end  824 total  840 skew    0 clock 119.05KHz
        v: height  600 start  616 end  624 total  640           clock 186.01Hz
  800x600 (0x1ca) 62.357MHz +HSync +VSync *current
        h: width   800 start  821 end  901 total 1040 skew    0 clock  59.96KHz
        v: height  600 start  601 end  604 total  632           clock  94.87Hz
  800x600 (0x1e0) 56.300MHz +HSync +VSync
        h: width   800 start  832 end  896 total 1048 skew    0 clock  53.72KHz
        v: height  600 start  601 end  604 total  631           clock  85.14Hz
  800x600 (0x1e1) 50.000MHz +HSync +VSync
        h: width   800 start  856 end  976 total 1040 skew    0 clock  48.08KHz
        v: height  600 start  637 end  643 total  666           clock  72.19Hz
  800x600 (0x1e2) 49.500MHz +HSync +VSync
        h: width   800 start  816 end  896 total 1056 skew    0 clock  46.88KHz
        v: height  600 start  601 end  604 total  625           clock  75.00Hz
  800x600 (0x1cb) 40.000MHz +HSync +VSync
        h: width   800 start  840 end  968 total 1056 skew    0 clock  37.88KHz
        v: height  600 start  601 end  605 total  628           clock  60.32Hz
  800x600 (0x1cc) 36.000MHz +HSync +VSync
        h: width   800 start  824 end  896 total 1024 skew    0 clock  35.16KHz
        v: height  600 start  601 end  603 total  625           clock  56.25Hz
  768x576 (0x1cd) 63.070MHz
        h: width   768 start  800 end  960 total 1024 skew    0 clock  61.59KHz
        v: height  576 start  578 end  590 total  616           clock  99.99Hz
  768x576 (0x1ce) 50.000MHz
        h: width   768 start  832 end  846 total 1000 skew    0 clock  50.00KHz
        v: height  576 start  590 end  595 total  630           clock  79.37Hz
  864x486 (0x1cf) 32.500MHz -HSync +VSync
        h: width   864 start  888 end  968 total 1072 skew    0 clock  30.32KHz
        v: height  486 start  489 end  494 total  506           clock  59.92Hz
  864x486 (0x1d0) 30.500MHz +HSync -VSync
        h: width   864 start  912 end  944 total 1024 skew    0 clock  29.79KHz
        v: height  486 start  489 end  494 total  500           clock  59.57Hz
  848x480 (0x1d1) 33.750MHz +HSync +VSync
        h: width   848 start  864 end  976 total 1088 skew    0 clock  31.02KHz
        v: height  480 start  486 end  494 total  517           clock  60.00Hz
  640x480 (0x1d2) 49.886MHz +HSync +VSync
        h: width   640 start  661 end  725 total  832 skew    0 clock  59.96KHz
        v: height  480 start  481 end  484 total  514           clock 116.65Hz
  640x480 (0x1e3) 36.000MHz -HSync -VSync
        h: width   640 start  696 end  752 total  832 skew    0 clock  43.27KHz
        v: height  480 start  481 end  484 total  509           clock  85.01Hz
  640x480 (0x1e4) 31.500MHz -HSync -VSync
        h: width   640 start  664 end  704 total  832 skew    0 clock  37.86KHz
        v: height  480 start  489 end  492 total  520           clock  72.81Hz
  640x480 (0x1e5) 31.500MHz -HSync -VSync
        h: width   640 start  656 end  720 total  840 skew    0 clock  37.50KHz
        v: height  480 start  481 end  484 total  500           clock  75.00Hz
  640x480 (0x1d3) 25.175MHz -HSync -VSync
        h: width   640 start  656 end  752 total  800 skew    0 clock  31.47KHz
        v: height  480 start  490 end  492 total  525           clock  59.94Hz
  720x405 (0x1d4) 22.500MHz -HSync +VSync
        h: width   720 start  744 end  808 total  896 skew    0 clock  25.11KHz
        v: height  405 start  408 end  413 total  422           clock  59.51Hz
  720x405 (0x1d5) 21.750MHz +HSync -VSync
        h: width   720 start  768 end  800 total  880 skew    0 clock  24.72KHz
        v: height  405 start  408 end  413 total  419           clock  58.99Hz
  720x400 (0x1e6) 35.500MHz -HSync +VSync
        h: width   720 start  756 end  828 total  936 skew    0 clock  37.93KHz
        v: height  400 start  401 end  404 total  446           clock  85.04Hz
  640x400 (0x1e7) 31.500MHz -HSync +VSync
        h: width   640 start  672 end  736 total  832 skew    0 clock  37.86KHz
        v: height  400 start  401 end  404 total  445           clock  85.08Hz
  640x360 (0x1d6) 18.000MHz -HSync +VSync
        h: width   640 start  664 end  720 total  800 skew    0 clock  22.50KHz
        v: height  360 start  363 end  368 total  376           clock  59.84Hz
  640x360 (0x1d7) 17.750MHz +HSync -VSync
        h: width   640 start  688 end  720 total  800 skew    0 clock  22.19KHz
        v: height  360 start  363 end  368 total  374           clock  59.32Hz
  640x350 (0x1e8) 31.500MHz +HSync -VSync
        h: width   640 start  672 end  736 total  832 skew    0 clock  37.86KHz
        v: height  350 start  382 end  385 total  445           clock  85.08Hz
  400x300 (0x1e9) 14.963MHz -HSync +VSync
        h: width   400 start  408 end  448 total  496 skew    0 clock  30.17KHz
        v: height  300 start  301 end  304 total  318           clock  94.87Hz
DP1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x44
   Timestamp:  34671
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
DP2 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x45
   Timestamp:  34671
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
HDMI1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x46
   Timestamp:  34671
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   max bpc: 12
      range: (8, 12)
   content type: No Data
      supported: No Data, Graphics, Photo, Cinema, Game
   Colorspace: Default
      supported: Default, SMPTE_170M_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, opRGB, BT2020_CYCC, BT2020_RGB, BT2020_YCC, DCI-P3_RGB_D65, DCI-P3_RGB_Theater
   aspect ratio: Automatic
      supported: Automatic, 4:3, 16:9
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x47
   Timestamp:  34671
   Subpixel:   no subpixels
   Clones:   
   CRTCs:      3
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   non-desktop: 0
      supported: 0, 1



Code: Select all
journalctl -ab|grep -i edid
Sep 13 15:34:19 introvertx95.extrovertdomain kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 13 15:34:19 introvertx95.extrovertdomain kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 13 15:35:16 introvertx95.extrovertdomain colord[5653]: failed to get edid data: EDID length is too small


Edid length is too small? :?:

/var/log/Xorg.0.log

Code: Select all
[    18.340] (--) Log file renamed from "/var/log/Xorg.pid-2858.log" to "/var/log/Xorg.0.log"
[    18.345]
X.Org X Server 1.20.9
X Protocol Version 11, Revision 0
[    18.345] Build Operating System: rabbit 5.6.8-server-1.mga7
[    18.345] Current Operating System: Linux introvertx95.extrovertdomain 5.8.8-1.mga8custom #2 SMP Sun Sep 13 12:53:32 JST 2020 x86_64
[    18.345] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.8-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin fbcon=rotate:1 splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
[    18.345] Build Date: 26 August 2020  07:12:27AM
[    18.345] Build ID: x11-server 1.20.9-7.mga8
[    18.345] Current version of pixman: 0.40.0
[    18.345]    Before reporting problems, check https://bugs.mageia.org
   to make sure that you have the latest version.
[    18.345] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    18.345] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep 13 15:34:30 2020
[    18.358] (==) Using config file: "/etc/X11/xorg.conf"
[    18.358] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    18.358] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    18.368] (==) ServerLayout "layout1"
[    18.368] (**) |-->Screen "screen1" (0)
[    18.368] (**) |   |-->Monitor "monitor1"
[    18.368] (**) |   |-->Device "device1"
[    18.368] (**) Option "DontZap" "False"
[    18.368] (**) Option "AllowMouseOpenFail"
[    18.368] (==) Automatically adding devices
[    18.368] (==) Automatically enabling devices
[    18.368] (==) Automatically adding GPU devices
[    18.368] (==) Automatically binding GPU devices
[    18.368] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    18.368] (==) FontPath set to:
   catalogue:/etc/X11/fontpath.d,
   built-ins
[    18.368] (**) ModulePath set to "/usr/lib64/xorg/extra-modules,/usr/lib64/xorg/modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    18.368] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[    18.368] (II) Loader magic: 0x61fd40
[    18.368] (II) Module ABI versions:
[    18.368]    X.Org ANSI C Emulation: 0.4
[    18.368]    X.Org Video Driver: 24.1
[    18.368]    X.Org XInput driver : 24.1
[    18.368]    X.Org Server Extension : 10.0
[    18.369] (++) using VT number 1

[    18.369] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[    18.369] (II) xfree86: Adding drm device (/dev/dri/card0)
[    18.369] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card0
[    18.380] (--) PCI:*(0@0:2:0) 8086:8a52:8086:2212 rev 7, Mem @ 0x601c000000/16777216, 0x4000000000/268435456, I/O @ 0x00004000/64, BIOS @ 0x????????/131072
[    18.380] (II) Open ACPI successful (/var/run/acpid.socket)
[    18.380] (II) "glx" will be loaded by default.
[    18.380] (II) LoadModule: "v4l"
[    18.380] (II) Loading /usr/lib64/xorg/modules/drivers/v4l_drv.so
[    18.380] (II) Module v4l: vendor="X.Org Foundation"
[    18.380]    compiled for 1.20.7, module version = 0.1.1
[    18.380]    ABI class: X.Org Video Driver, version 24.1
[    18.380] (II) LoadModule: "glx"
[    18.380] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so
[    18.381] (II) Module glx: vendor="X.Org Foundation"
[    18.381]    compiled for 1.20.9, module version = 1.0.0
[    18.381]    ABI class: X.Org Server Extension, version 10.0
[    18.381] (II) LoadModule: "intel"
[    18.381] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so
[    18.387] (II) Module intel: vendor="X.Org Foundation"
[    18.387]    compiled for 1.20.8, module version = 2.99.917
[    18.387]    Module class: X.Org Video Driver
[    18.387]    ABI class: X.Org Video Driver, version 24.1
[    18.387] (II) v4l driver for Video4Linux overlay mode (V4L2)
[    18.388] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
   i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
   915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
   Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
   GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[    18.388] (II) intel: Driver for Intel(R) HD Graphics
[    18.388] (II) intel: Driver for Intel(R) Iris(TM) Graphics
[    18.388] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics
[    18.388] (WW) Falling back to old probe method for v4l
[    18.388] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20200515
[    18.400] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[    18.400] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2; using a maximum of 4 threads
[    18.400] (II) intel(0): Creating default Display subsection in Screen section
   "screen1" for depth/fbbpp 24/32
[    18.400] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[    18.400] (==) intel(0): RGB weight 888
[    18.400] (==) intel(0): Default visual is TrueColor
[    18.400] (II) intel(0): Output eDP1 using monitor section monitor1
[    18.401] (**) intel(0): Found backlight control interface intel_backlight (type 'raw') for output eDP1
[    18.401] (II) intel(0): Enabled output eDP1
[    18.401] (II) intel(0): Output HDMI1 has no monitor section
[    18.401] (II) intel(0): Enabled output HDMI1
[    18.401] (II) intel(0): Output DP1 has no monitor section
[    18.401] (II) intel(0): Enabled output DP1
[    18.401] (II) intel(0): Output DP2 has no monitor section
[    18.401] (II) intel(0): Enabled output DP2
[    18.401] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[    18.401] (II) intel(0): Output VIRTUAL1 has no monitor section
[    18.401] (II) intel(0): Enabled output VIRTUAL1
[    18.401] (--) intel(0): Output eDP1 using initial mode 1024x768 on pipe 0
[    18.411] (==) intel(0): TearFree enabled
[    18.411] (==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
[    18.411] (==) intel(0): DPI set to (96, 96)
[    18.411] (II) Loading sub module "dri3"
[    18.411] (II) LoadModule: "dri3"
[    18.411] (II) Module "dri3" already built-in
[    18.411] (II) Loading sub module "dri2"
[    18.411] (II) LoadModule: "dri2"
[    18.411] (II) Module "dri2" already built-in
[    18.411] (II) Loading sub module "present"
[    18.411] (II) LoadModule: "present"
[    18.411] (II) Module "present" already built-in
[    18.435] (II) intel(0): SNA initialized with Skylake (gen9) backend
[    18.435] (==) intel(0): Backing store enabled
[    18.435] (==) intel(0): Silken mouse enabled
[    18.440] (II) intel(0): HW Cursor enabled
[    18.440] (**) intel(0): DPMS enabled
[    18.440] (==) intel(0): Display hotplug detection enabled
[    18.440] (II) intel(0): [DRI2] Setup complete
[    18.440] (II) intel(0): [DRI2]   DRI driver: i965
[    18.440] (II) intel(0): [DRI2]   VDPAU driver: va_gl
[    18.440] (II) intel(0): direct rendering: DRI2 DRI3 enabled
[    18.440] (II) intel(0): hardware support for Present enabled
[    18.440] (II) Initializing extension Generic Event Extension
[    18.440] (II) Initializing extension SHAPE
[    18.440] (II) Initializing extension MIT-SHM
[    18.440] (II) Initializing extension XInputExtension
[    18.443] (II) Initializing extension XTEST
[    18.443] (II) Initializing extension BIG-REQUESTS
[    18.443] (II) Initializing extension SYNC
[    18.443] (II) Initializing extension XKEYBOARD
[    18.443] (II) Initializing extension XC-MISC
[    18.443] (II) Initializing extension SECURITY
[    18.444] (II) Initializing extension XFIXES
[    18.444] (II) Initializing extension RENDER
[    18.444] (II) Initializing extension RANDR
[    18.444] (II) Initializing extension COMPOSITE
[    18.444] (II) Initializing extension DAMAGE
[    18.444] (II) Initializing extension MIT-SCREEN-SAVER
[    18.444] (II) Initializing extension DOUBLE-BUFFER
[    18.444] (II) Initializing extension RECORD
[    18.444] (II) Initializing extension DPMS
[    18.444] (II) Initializing extension Present
[    18.444] (II) Initializing extension DRI3
[    18.444] (II) Initializing extension X-Resource
[    18.444] (II) Initializing extension XVideo
[    18.445] (II) Initializing extension XVideo-MotionCompensation
[    18.445] (II) Initializing extension GLX
[    18.589] (II) AIGLX: Loaded and initialized i965
[    18.589] (II) GLX: Initialized DRI2 GL provider for screen 0
[    18.589] (II) Initializing extension XFree86-VidModeExtension
[    18.589] (II) Initializing extension XFree86-DGA
[    18.589] (II) Initializing extension XFree86-DRI
[    18.591] (II) Initializing extension DRI2
[    18.593] (II) intel(0): switch to mode 1024x768@60.0 on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[    18.595] (II) intel(0): Setting screen physical size to 270 x 203
[    18.768] (II) config/udev: Adding input device Power Button (/dev/input/event11)
[    18.768] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    18.768] (**) Power Button: Applying InputClass "system-keyboard"
[    18.768] (II) LoadModule: "libinput"
[    18.768] (II) Loading /usr/lib64/xorg/modules/input/libinput_drv.so
[    18.769] (II) Module libinput: vendor="X.Org Foundation"
[    18.769]    compiled for 1.20.8, module version = 0.30.0
[    18.769]    Module class: X.Org XInput Driver
[    18.769]    ABI class: X.Org XInput driver, version 24.1
[    18.769] (II) Using input driver 'libinput' for 'Power Button'
[    18.769] (**) Power Button: always reports core events
[    18.769] (**) Option "Device" "/dev/input/event11"
[    18.769] (**) Option "_source" "server/udev"
[    18.800] (II) event11 - Power Button: is tagged by udev as: Keyboard
[    18.800] (II) event11 - Power Button: device is a keyboard
[    18.800] (II) event11 - Power Button: device removed
[    18.808] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input11/event11"
[    18.808] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    18.808] (**) Option "xkb_model" "pc105"
[    18.808] (**) Option "xkb_layout" "us"
[    18.808] (**) Option "xkb_options" "compose:rwin"
[    18.821] (II) event11 - Power Button: is tagged by udev as: Keyboard
[    18.821] (II) event11 - Power Button: device is a keyboard
[    18.821] (II) config/udev: Adding input device Video Bus (/dev/input/event1)
[    18.821] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    18.821] (**) Video Bus: Applying InputClass "system-keyboard"
[    18.821] (II) Using input driver 'libinput' for 'Video Bus'
[    18.821] (**) Video Bus: always reports core events
[    18.821] (**) Option "Device" "/dev/input/event1"
[    18.821] (**) Option "_source" "server/udev"
[    18.822] (II) event1  - Video Bus: is tagged by udev as: Keyboard
[    18.822] (II) event1  - Video Bus: device is a keyboard
[    18.822] (II) event1  - Video Bus: device removed
[    18.834] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input1/event1"
[    18.834] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    18.834] (**) Option "xkb_model" "pc105"
[    18.834] (**) Option "xkb_layout" "us"
[    18.834] (**) Option "xkb_options" "compose:rwin"
[    18.834] (II) event1  - Video Bus: is tagged by udev as: Keyboard
[    18.834] (II) event1  - Video Bus: device is a keyboard
[    18.835] (II) config/udev: Adding input device Lid Switch (/dev/input/event8)
[    18.835] (II) No input driver specified, ignoring this device.
[    18.835] (II) This device may have been added with another device file.
[    18.835] (II) config/udev: Adding input device Power Button (/dev/input/event10)
[    18.835] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    18.835] (**) Power Button: Applying InputClass "system-keyboard"
[    18.835] (II) Using input driver 'libinput' for 'Power Button'
[    18.835] (**) Power Button: always reports core events
[    18.835] (**) Option "Device" "/dev/input/event10"
[    18.835] (**) Option "_source" "server/udev"
[    18.835] (II) event10 - Power Button: is tagged by udev as: Keyboard
[    18.835] (II) event10 - Power Button: device is a keyboard
[    18.835] (II) event10 - Power Button: device removed
[    18.843] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input10/event10"
[    18.843] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    18.843] (**) Option "xkb_model" "pc105"
[    18.843] (**) Option "xkb_layout" "us"
[    18.843] (**) Option "xkb_options" "compose:rwin"
[    18.843] (II) event10 - Power Button: is tagged by udev as: Keyboard
[    18.844] (II) event10 - Power Button: device is a keyboard
[    18.844] (II) config/udev: Adding input device Sleep Button (/dev/input/event9)
[    18.844] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    18.844] (**) Sleep Button: Applying InputClass "system-keyboard"
[    18.844] (II) Using input driver 'libinput' for 'Sleep Button'
[    18.844] (**) Sleep Button: always reports core events
[    18.844] (**) Option "Device" "/dev/input/event9"
[    18.844] (**) Option "_source" "server/udev"
[    18.845] (II) event9  - Sleep Button: is tagged by udev as: Keyboard
[    18.845] (II) event9  - Sleep Button: device is a keyboard
[    18.845] (II) event9  - Sleep Button: device removed
[    18.854] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input9/event9"
[    18.854] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    18.854] (**) Option "xkb_model" "pc105"
[    18.854] (**) Option "xkb_layout" "us"
[    18.854] (**) Option "xkb_options" "compose:rwin"
[    18.854] (II) event9  - Sleep Button: is tagged by udev as: Keyboard
[    18.854] (II) event9  - Sleep Button: device is a keyboard
[    18.855] (II) config/udev: Adding input device HID 6901:2701 (/dev/input/event2)
[    18.855] (**) HID 6901:2701: Applying InputClass "libinput keyboard catchall"
[    18.855] (**) HID 6901:2701: Applying InputClass "system-keyboard"
[    18.855] (II) Using input driver 'libinput' for 'HID 6901:2701'
[    18.855] (**) HID 6901:2701: always reports core events
[    18.855] (**) Option "Device" "/dev/input/event2"
[    18.855] (**) Option "_source" "server/udev"
[    18.856] (II) event2  - HID 6901:2701: is tagged by udev as: Keyboard
[    18.856] (II) event2  - HID 6901:2701: device is a keyboard
[    18.856] (II) event2  - HID 6901:2701: device removed
[    18.870] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.0/0003:6901:2701.0001/input/input2/event2"
[    18.870] (II) XINPUT: Adding extended input device "HID 6901:2701" (type: KEYBOARD, id 10)
[    18.870] (**) Option "xkb_model" "pc105"
[    18.870] (**) Option "xkb_layout" "us"
[    18.870] (**) Option "xkb_options" "compose:rwin"
[    18.871] (II) event2  - HID 6901:2701: is tagged by udev as: Keyboard
[    18.871] (II) event2  - HID 6901:2701: device is a keyboard
[    18.872] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/event3)
[    18.872] (**) HID 6901:2701 Mouse: Applying InputClass "libinput pointer catchall"
[    18.872] (II) Using input driver 'libinput' for 'HID 6901:2701 Mouse'
[    18.872] (**) HID 6901:2701 Mouse: always reports core events
[    18.872] (**) Option "Device" "/dev/input/event3"
[    18.872] (**) Option "_source" "server/udev"
[    18.873] (II) event3  - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[    18.873] (II) event3  - HID 6901:2701 Mouse: device is a pointer
[    18.873] (II) event3  - HID 6901:2701 Mouse: device removed
[    18.884] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input3/event3"
[    18.884] (II) XINPUT: Adding extended input device "HID 6901:2701 Mouse" (type: MOUSE, id 11)
[    18.884] (**) Option "AccelerationScheme" "none"
[    18.884] (**) HID 6901:2701 Mouse: (accel) selected scheme none/0
[    18.884] (**) HID 6901:2701 Mouse: (accel) acceleration factor: 2.000
[    18.884] (**) HID 6901:2701 Mouse: (accel) acceleration threshold: 4
[    18.886] (II) event3  - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[    18.886] (II) event3  - HID 6901:2701 Mouse: device is a pointer
[    18.887] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/mouse0)
[    18.887] (II) No input driver specified, ignoring this device.
[    18.887] (II) This device may have been added with another device file.
[    18.887] (II) config/udev: Adding input device HID 6901:2701 Consumer Control (/dev/input/event4)
[    18.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[    18.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[    18.888] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[    18.888] (**) HID 6901:2701 Consumer Control: always reports core events
[    18.888] (**) Option "Device" "/dev/input/event4"
[    18.888] (**) Option "_source" "server/udev"
[    18.889] (II) event4  - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[    18.889] (II) event4  - HID 6901:2701 Consumer Control: device is a keyboard
[    18.889] (II) event4  - HID 6901:2701 Consumer Control: device removed
[    18.897] (II) libinput: HID 6901:2701 Consumer Control: needs a virtual subdevice
[    18.897] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[    18.897] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: MOUSE, id 12)
[    18.897] (**) Option "AccelerationScheme" "none"
[    18.897] (**) HID 6901:2701 Consumer Control: (accel) selected scheme none/0
[    18.897] (**) HID 6901:2701 Consumer Control: (accel) acceleration factor: 2.000
[    18.897] (**) HID 6901:2701 Consumer Control: (accel) acceleration threshold: 4
[    18.898] (II) event4  - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[    18.898] (II) event4  - HID 6901:2701 Consumer Control: device is a keyboard
[    18.899] (II) config/udev: Adding input device HID 6901:2701 System Control (/dev/input/event5)
[    18.899] (**) HID 6901:2701 System Control: Applying InputClass "libinput keyboard catchall"
[    18.899] (**) HID 6901:2701 System Control: Applying InputClass "system-keyboard"
[    18.899] (II) Using input driver 'libinput' for 'HID 6901:2701 System Control'
[    18.899] (**) HID 6901:2701 System Control: always reports core events
[    18.899] (**) Option "Device" "/dev/input/event5"
[    18.899] (**) Option "_source" "server/udev"
[    18.900] (II) event5  - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[    18.900] (II) event5  - HID 6901:2701 System Control: device is a keyboard
[    18.900] (II) event5  - HID 6901:2701 System Control: device removed
[    18.910] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input5/event5"
[    18.910] (II) XINPUT: Adding extended input device "HID 6901:2701 System Control" (type: KEYBOARD, id 13)
[    18.910] (**) Option "xkb_model" "pc105"
[    18.910] (**) Option "xkb_layout" "us"
[    18.910] (**) Option "xkb_options" "compose:rwin"
[    18.911] (II) event5  - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[    18.911] (II) event5  - HID 6901:2701 System Control: device is a keyboard
[    18.911] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/event6)
[    18.911] (**)   Mouse for Windows: Applying InputClass "libinput pointer catchall"
[    18.911] (II) Using input driver 'libinput' for '  Mouse for Windows'
[    18.911] (**)   Mouse for Windows: always reports core events
[    18.911] (**) Option "Device" "/dev/input/event6"
[    18.911] (**) Option "_source" "server/udev"
[    18.963] (II) event6  -   Mouse for Windows: is tagged by udev as: Mouse
[    18.963] (II) event6  -   Mouse for Windows: device is a pointer
[    18.963] (II) event6  -   Mouse for Windows: device removed
[    18.976] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.0/0003:2F24:0118.0003/input/input6/event6"
[    18.976] (II) XINPUT: Adding extended input device "  Mouse for Windows" (type: MOUSE, id 14)
[    18.976] (**) Option "AccelerationScheme" "none"
[    18.976] (**)   Mouse for Windows: (accel) selected scheme none/0
[    18.976] (**)   Mouse for Windows: (accel) acceleration factor: 2.000
[    18.976] (**)   Mouse for Windows: (accel) acceleration threshold: 4
[    19.033] (II) event6  -   Mouse for Windows: is tagged by udev as: Mouse
[    19.033] (II) event6  -   Mouse for Windows: device is a pointer
[    19.036] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/mouse1)
[    19.036] (II) No input driver specified, ignoring this device.
[    19.037] (II) This device may have been added with another device file.
[    19.039] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/event7)
[    19.039] (**)   Mouse for Windows: Applying InputClass "libinput keyboard catchall"
[    19.039] (**)   Mouse for Windows: Applying InputClass "system-keyboard"
[    19.039] (II) Using input driver 'libinput' for '  Mouse for Windows'
[    19.039] (**)   Mouse for Windows: always reports core events
[    19.039] (**) Option "Device" "/dev/input/event7"
[    19.039] (**) Option "_source" "server/udev"
[    19.045] (II) event7  -   Mouse for Windows: is tagged by udev as: Keyboard
[    19.045] (II) event7  -   Mouse for Windows: device is a keyboard
[    19.046] (II) event7  -   Mouse for Windows: device removed
[    19.059] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.1/0003:2F24:0118.0004/input/input7/event7"
[    19.059] (II) XINPUT: Adding extended input device "  Mouse for Windows" (type: KEYBOARD, id 15)
[    19.059] (**) Option "xkb_model" "pc105"
[    19.059] (**) Option "xkb_layout" "us"
[    19.059] (**) Option "xkb_options" "compose:rwin"
[    19.065] (II) event7  -   Mouse for Windows: is tagged by udev as: Keyboard
[    19.066] (II) event7  -   Mouse for Windows: device is a keyboard
[    19.068] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/event14)
[    19.068] (**) HTIX5288:00 093A:0255 Mouse: Applying InputClass "libinput pointer catchall"
[    19.068] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Mouse'
[    19.068] (**) HTIX5288:00 093A:0255 Mouse: always reports core events
[    19.068] (**) Option "Device" "/dev/input/event14"
[    19.068] (**) Option "_source" "server/udev"
[    19.071] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[    19.072] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[    19.074] (II) event14 - HTIX5288:00 093A:0255 Mouse: device removed
[    19.091] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input17/event14"
[    19.091] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Mouse" (type: MOUSE, id 16)
[    19.091] (**) Option "AccelerationScheme" "none"
[    19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) selected scheme none/0
[    19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration factor: 2.000
[    19.091] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration threshold: 4
[    19.097] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[    19.098] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[    19.102] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/mouse2)
[    19.102] (II) No input driver specified, ignoring this device.
[    19.102] (II) This device may have been added with another device file.
[    19.103] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/event15)
[    19.103] (**) HTIX5288:00 093A:0255 Touchpad: Applying InputClass "libinput touchpad catchall"
[    19.103] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Touchpad'
[    19.103] (**) HTIX5288:00 093A:0255 Touchpad: always reports core events
[    19.103] (**) Option "Device" "/dev/input/event15"
[    19.103] (**) Option "_source" "server/udev"
[    19.106] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[    19.106] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[    19.107] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[    19.107] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device removed
[    19.127] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input18/event15"
[    19.127] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Touchpad" (type: TOUCHPAD, id 17)
[    19.127] (**) Option "AccelerationScheme" "none"
[    19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) selected scheme none/0
[    19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration factor: 2.000
[    19.127] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration threshold: 4
[    19.128] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[    19.128] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[    19.129] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[    19.129] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/mouse3)
[    19.129] (II) No input driver specified, ignoring this device.
[    19.129] (II) This device may have been added with another device file.
[    19.129] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/event16)
[    19.129] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[    19.130] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[    19.130] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[    19.130] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[    19.130] (**) Goodix Capacitive TouchScreen: always reports core events
[    19.130] (**) Option "Device" "/dev/input/event16"
[    19.130] (**) Option "_source" "server/udev"
[    19.130] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[    19.130] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[    19.130] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[    19.130] (II) event16 - Goodix Capacitive TouchScreen: device removed
[    19.147] (II) libinput: Goodix Capacitive TouchScreen: needs a virtual subdevice
[    19.147] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[    19.147] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: TOUCHSCREEN, id 18)
[    19.147] (**) Option "AccelerationScheme" "none"
[    19.147] (**) Goodix Capacitive TouchScreen: (accel) selected scheme none/0
[    19.147] (**) Goodix Capacitive TouchScreen: (accel) acceleration factor: 2.000
[    19.147] (**) Goodix Capacitive TouchScreen: (accel) acceleration threshold: 4
[    19.147] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[    19.147] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[    19.147] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[    19.148] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/mouse4)
[    19.148] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[    19.148] (II) No input driver specified, ignoring this device.
[    19.148] (II) This device may have been added with another device file.
[    19.148] (II) config/udev: Adding input device Intel HID events (/dev/input/event12)
[    19.148] (**) Intel HID events: Applying InputClass "libinput keyboard catchall"
[    19.148] (**) Intel HID events: Applying InputClass "system-keyboard"
[    19.148] (II) Using input driver 'libinput' for 'Intel HID events'
[    19.148] (**) Intel HID events: always reports core events
[    19.148] (**) Option "Device" "/dev/input/event12"
[    19.148] (**) Option "_source" "server/udev"
[    19.149] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[    19.149] (II) event12 - Intel HID events: device is a keyboard
[    19.149] (II) event12 - Intel HID events: device removed
[    19.159] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input12/event12"
[    19.159] (II) XINPUT: Adding extended input device "Intel HID events" (type: KEYBOARD, id 19)
[    19.159] (**) Option "xkb_model" "pc105"
[    19.159] (**) Option "xkb_layout" "us"
[    19.159] (**) Option "xkb_options" "compose:rwin"
[    19.159] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[    19.159] (II) event12 - Intel HID events: device is a keyboard
[    19.160] (II) config/udev: Adding input device Intel HID 5 button array (/dev/input/event13)
[    19.160] (**) Intel HID 5 button array: Applying InputClass "libinput keyboard catchall"
[    19.160] (**) Intel HID 5 button array: Applying InputClass "system-keyboard"
[    19.160] (II) Using input driver 'libinput' for 'Intel HID 5 button array'
[    19.160] (**) Intel HID 5 button array: always reports core events
[    19.160] (**) Option "Device" "/dev/input/event13"
[    19.160] (**) Option "_source" "server/udev"
[    19.160] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[    19.160] (II) event13 - Intel HID 5 button array: device is a keyboard
[    19.160] (II) event13 - Intel HID 5 button array: device removed
[    19.171] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input13/event13"
[    19.171] (II) XINPUT: Adding extended input device "Intel HID 5 button array" (type: KEYBOARD, id 20)
[    19.171] (**) Option "xkb_model" "pc105"
[    19.171] (**) Option "xkb_layout" "us"
[    19.171] (**) Option "xkb_options" "compose:rwin"
[    19.171] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[    19.171] (II) event13 - Intel HID 5 button array: device is a keyboard
[    19.172] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event17)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event18)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event19)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event20)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event21)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event22)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.172] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=10 (/dev/input/event23)
[    19.172] (II) No input driver specified, ignoring this device.
[    19.172] (II) This device may have been added with another device file.
[    19.173] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=11 (/dev/input/event24)
[    19.173] (II) No input driver specified, ignoring this device.
[    19.173] (II) This device may have been added with another device file.
[    19.173] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=12 (/dev/input/event25)
[    19.173] (II) No input driver specified, ignoring this device.
[    19.173] (II) This device may have been added with another device file.
[    19.173] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    19.173] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    19.173] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[    19.173] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    19.173] (**) AT Translated Set 2 keyboard: always reports core events
[    19.173] (**) Option "Device" "/dev/input/event0"
[    19.173] (**) Option "_source" "server/udev"
[    19.174] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    19.174] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[    19.174] (II) event0  - AT Translated Set 2 keyboard: device removed
[    19.183] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    19.183] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 21)
[    19.183] (**) Option "xkb_model" "pc105"
[    19.183] (**) Option "xkb_layout" "us"
[    19.183] (**) Option "xkb_options" "compose:rwin"
[    19.183] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    19.183] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[    19.212] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[    19.212] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[    19.212] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[    19.212] (**) HID 6901:2701 Consumer Control: always reports core events
[    19.212] (**) Option "Device" "/dev/input/event4"
[    19.212] (**) Option "_source" "_driver/libinput"
[    19.212] (II) libinput: HID 6901:2701 Consumer Control: is a virtual subdevice
[    19.212] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[    19.212] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: KEYBOARD, id 22)
[    19.212] (**) Option "xkb_model" "pc105"
[    19.212] (**) Option "xkb_layout" "us"
[    19.212] (**) Option "xkb_options" "compose:rwin"
[    19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[    19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[    19.212] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[    19.212] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[    19.212] (**) Goodix Capacitive TouchScreen: always reports core events
[    19.212] (**) Option "Device" "/dev/input/event16"
[    19.212] (**) Option "_source" "_driver/libinput"
[    19.212] (II) libinput: Goodix Capacitive TouchScreen: is a virtual subdevice
[    19.212] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[    19.212] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: KEYBOARD, id 23)
[    19.212] (**) Option "xkb_model" "pc105"
[    19.212] (**) Option "xkb_layout" "us"
[    19.212] (**) Option "xkb_options" "compose:rwin"
[    19.217] (EE) Failed to open authorization file "/var/run/sddm/{ef2571fe-2c16-47ce-bab6-adb31b0af8ba}": No such file or directory
[    34.669] (II) intel(0): resizing framebuffer to 600x800
[    34.671] (II) intel(0): switch to mode 800x600@94.9 on eDP1 using pipe 0, position (0, 0), rotation right, reflection none
[    99.625] (EE) intel(0): Failed to submit rendering commands (Input/output error), disabling acceleration.
[    99.625] (EE) intel(0): When reporting this, please include /sys/class/drm/card0/error and the full dmesg.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 13th, '20, 10:45

I have an odd question... this question is:

IN other distros I tested, just to see what is going on earlier. the command you gave me, fbcon=rotate:1, I can't remember 1 where if I just stuck it in grub with a quick edit, it rotated. It everything else wasn't right but it at least rotated to the right.

Why is this basic thing not working in Mageia? Neither in live or installed. Went back and tried a few lives? So it seems that parameters are really NOT being honored in when they should be passed to the kernel?

Can anyone else try with some lives and observe this? Unless it is only with this weird hardware. But with this hardware it works with other distros. None I would use and most don't even make it to X like Mageia here.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 13th, '20, 19:24

From what I can tell, only CONFIG_DRM_KMS_HELPER needs to be either enabled or configured as a module, and CONFIG_DRM_LOAD_EDID_FIRMWARE needs to be enabled.

But it does not seem to do anything from your logs, but it could also be that this is because you're running a wayland session. I can only suggest to try with a legacy X session, not using wayland as already suggested before several times.

Can you post the ouput of
Code: Select all
zgrep -i -e edid -e drm /proc/config.gz

and also /var/log/Xorg.0.log after your modifications?
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 14th, '20, 00:10

Both... I can send the logs from Xfce but I think I did that the first time. But then I didn't have everything enabled. :oops:

I can do it later when I am back home and can open up that unit.

Either way the result is the same. Sometimes I end up in KDE Wayland because:

1. xrandr rotate killed X plasma. All I get is a cursor and black screen and seem unable to bring it back. (any suggestions? Isn't there something like deleting user settings that will revert it to default)

2. Sometimes aside from already taking as long as 3 min or more to show up, Xfce X session does not show up after login. So I end up resetting X and going to Plasma Wayland.

I actually finished in Xfce yesterday but it seems like I had to go into Plasma Wayland then logout and come back to Xfce. Xfce just didn't start at first.

I recompiled because an update dropped in a new kernel. 5.8.9. So I set it up because redoing 5.8.8 for some reason wifi was starting quite late and the applet was never showing when it was online.
Of course in Wayland, I can't open MCC. So mostly I try to work in Xfce if I can get it open.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 14th, '20, 00:12

I would like to do a FRESH install with just Xfce.

Can you tell me how I can get an RPM from this kernel as that doesn't work.

Is there a different set of commands or something I need to download to get it to make an RPM?
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 14th, '20, 17:30

If XFCE does not show up after 3 minutes or more, you should better check the logs to find out why. A simple reinstallation will usually not fix anything. You can easily test if it's an issue with your user configuration by simply creating a new user and loggin in as that user.

Also I don't think you mentioned at all that xrandr rotate crashes your X session, or that XFCE does not start at all.

And no, I can't tell you how to create an rpm from your self-compiled kernel. I've not done this in ages myself because I didn't need to.
And as you mentioned that you needed to recompile due to 5.8.9 what would that achieve if you would have to redo it for each kernel update?
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 15th, '20, 00:38

Sabungayam wrote:I recompiled because an update dropped in a new kernel. 5.8.9. So I set it up because redoing 5.8.8 for some reason wifi was starting quite late and the applet was never showing when it was online.
Of course in Wayland, I can't open MCC. So mostly I try to work in Xfce if I can get it open.


My reason for trying the new kernel.

I mentioned about xrandr because something had been mentioned about it on the page with this custom edid. That using it to rotate breaks the vsync. I said earlier here that it had indeed broken
plasma. So I installed Plasma Wayland. Pretty far back. No time to find it now on my way out.

xfce was pretty slow, to start and I presumed because of this screen issue. But lately after the recompile it has gotten to this state of taking longer to start or not starting at all.

using 5.8.9 has my wifi starting back normally as well as the applet registering changes properly. I apologize as I didn't have time to get on that computer yesterday for the logs. Hopefully today.

Which log should I check for the xfce issue?
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 15th, '20, 16:58

As with everything else, journal logs. journalctl -ab and then check for events during/after the time when XFCE was started.
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 16th, '20, 11:01

Code: Select all
 
#zgrep -i -e edid -e drm /proc/config.gz
CONFIG_DRM=m
CONFIG_DRM_MIPI_DSI=y
# CONFIG_DRM_DP_AUX_CHARDEV is not set
# CONFIG_DRM_DEBUG_SELFTEST is not set
CONFIG_DRM_KMS_HELPER=m
CONFIG_DRM_KMS_FB_HELPER=y
# CONFIG_DRM_DEBUG_DP_MST_TOPOLOGY_REFS is not set
CONFIG_DRM_FBDEV_EMULATION=y
CONFIG_DRM_FBDEV_OVERALLOC=100
# CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM is not set
CONFIG_DRM_LOAD_EDID_FIRMWARE=y
CONFIG_DRM_DP_CEC=y
CONFIG_DRM_TTM=m
CONFIG_DRM_TTM_DMA_PAGE_POOL=y
CONFIG_DRM_VRAM_HELPER=m
CONFIG_DRM_TTM_HELPER=m
CONFIG_DRM_GEM_SHMEM_HELPER=y
CONFIG_DRM_VM=y
CONFIG_DRM_SCHED=m
CONFIG_DRM_I2C_CH7006=m
CONFIG_DRM_I2C_SIL164=m
CONFIG_DRM_I2C_NXP_TDA998X=m
CONFIG_DRM_I2C_NXP_TDA9950=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_RADEON_USERPTR=y
CONFIG_DRM_AMDGPU=m
CONFIG_DRM_AMDGPU_SI=y
CONFIG_DRM_AMDGPU_CIK=y
CONFIG_DRM_AMDGPU_USERPTR=y
# CONFIG_DRM_AMDGPU_GART_DEBUGFS is not set
CONFIG_DRM_AMD_ACP=y
CONFIG_DRM_AMD_DC=y
CONFIG_DRM_AMD_DC_DCN=y
CONFIG_DRM_AMD_DC_HDCP=y
CONFIG_DRM_NOUVEAU=m
CONFIG_DRM_NOUVEAU_BACKLIGHT=y
CONFIG_DRM_I915=m
CONFIG_DRM_I915_FORCE_PROBE="*"
CONFIG_DRM_I915_CAPTURE_ERROR=y
CONFIG_DRM_I915_COMPRESS_ERROR=y
CONFIG_DRM_I915_USERPTR=y
# CONFIG_DRM_I915_GVT is not set
# drm/i915 Debugging
# CONFIG_DRM_I915_WERROR is not set
# CONFIG_DRM_I915_DEBUG is not set
# CONFIG_DRM_I915_DEBUG_MMIO is not set
# CONFIG_DRM_I915_SW_FENCE_DEBUG_OBJECTS is not set
# CONFIG_DRM_I915_SW_FENCE_CHECK_DAG is not set
# CONFIG_DRM_I915_DEBUG_GUC is not set
# CONFIG_DRM_I915_SELFTEST is not set
# CONFIG_DRM_I915_LOW_LEVEL_TRACEPOINTS is not set
# CONFIG_DRM_I915_DEBUG_VBLANK_EVADE is not set
# CONFIG_DRM_I915_DEBUG_RUNTIME_PM is not set
# end of drm/i915 Debugging
# drm/i915 Profile Guided Optimisation
CONFIG_DRM_I915_FENCE_TIMEOUT=10000
CONFIG_DRM_I915_USERFAULT_AUTOSUSPEND=250
CONFIG_DRM_I915_HEARTBEAT_INTERVAL=2500
CONFIG_DRM_I915_PREEMPT_TIMEOUT=640
CONFIG_DRM_I915_MAX_REQUEST_BUSYWAIT=8000
CONFIG_DRM_I915_STOP_TIMEOUT=100
CONFIG_DRM_I915_TIMESLICE_DURATION=1
# end of drm/i915 Profile Guided Optimisation
CONFIG_DRM_VGEM=m
# CONFIG_DRM_VKMS is not set
CONFIG_DRM_VMWGFX=m
# CONFIG_DRM_VMWGFX_FBCON is not set
CONFIG_DRM_GMA500=m
CONFIG_DRM_GMA600=y
CONFIG_DRM_GMA3600=y
CONFIG_DRM_UDL=m
CONFIG_DRM_AST=m
CONFIG_DRM_MGAG200=m
CONFIG_DRM_QXL=m
CONFIG_DRM_BOCHS=m
CONFIG_DRM_VIRTIO_GPU=m
CONFIG_DRM_PANEL=y
# CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN is not set
CONFIG_DRM_BRIDGE=y
CONFIG_DRM_PANEL_BRIDGE=y
# CONFIG_DRM_ANALOGIX_ANX78XX is not set
# CONFIG_DRM_ETNAVIV is not set
CONFIG_DRM_CIRRUS_QEMU=m
CONFIG_DRM_GM12U320=m
# CONFIG_TINYDRM_HX8357D is not set
# CONFIG_TINYDRM_ILI9225 is not set
# CONFIG_TINYDRM_ILI9341 is not set
# CONFIG_TINYDRM_ILI9486 is not set
# CONFIG_TINYDRM_MI0283QT is not set
# CONFIG_TINYDRM_REPAPER is not set
# CONFIG_TINYDRM_ST7586 is not set
# CONFIG_TINYDRM_ST7735R is not set
CONFIG_DRM_XEN=y
CONFIG_DRM_XEN_FRONTEND=m
CONFIG_DRM_VBOXVIDEO=m
CONFIG_DRM_LEGACY=y
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_I810=m
CONFIG_DRM_MGA=m
CONFIG_DRM_SIS=m
# CONFIG_DRM_VIA is not set
CONFIG_DRM_SAVAGE=m
CONFIG_DRM_PANEL_ORIENTATION_QUIRKS=y
CONFIG_FIRMWARE_EDID=y


Code: Select all
[root@introvertx95 Desktop]# journalctl -ab|grep -i edid
Sep 16 17:27:07 introvertx95.extrovertdomain kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-5.8.9-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 16 17:27:07 introvertx95.extrovertdomain kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.9-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
Sep 16 17:31:39 introvertx95.extrovertdomain colord[22279]: failed to get edid data: EDID length is too small



Code: Select all
# xrandr --verbose
Screen 0: minimum 8 x 8, current 600 x 800, maximum 32767 x 32767
eDP1 connected primary 600x800+0+0 (0x1c5) right (normal left inverted right x axis y axis) 0mm x 0mm
   Identifier: 0x43
   Timestamp:  410126
   Subpixel:   unknown
   Gamma:      1.0:1.0:1.0
   Brightness: 1.0
   Clones:   
   CRTC:       0
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   BACKLIGHT: 480
      range: (0, 480)
   Backlight: 480
      range: (0, 480)
   scaling mode: Full aspect
      supported: Full, Center, Full aspect
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
  1024x768 (0x49) 65.000MHz -HSync -VSync
        h: width  1024 start 1048 end 1184 total 1344 skew    0 clock  48.36KHz
        v: height  768 start  771 end  777 total  806           clock  60.00Hz
  1024x576 (0x1c1) 46.500MHz -HSync +VSync
        h: width  1024 start 1064 end 1160 total 1296 skew    0 clock  35.88KHz
        v: height  576 start  579 end  584 total  599           clock  59.90Hz
  1024x576 (0x1c2) 42.000MHz +HSync -VSync
        h: width  1024 start 1072 end 1104 total 1184 skew    0 clock  35.47KHz
        v: height  576 start  579 end  584 total  593           clock  59.82Hz
  960x540 (0x1c3) 40.750MHz -HSync +VSync
        h: width   960 start  992 end 1088 total 1216 skew    0 clock  33.51KHz
        v: height  540 start  543 end  548 total  562           clock  59.63Hz
  960x540 (0x1c4) 37.250MHz +HSync -VSync
        h: width   960 start 1008 end 1040 total 1120 skew    0 clock  33.26KHz
        v: height  540 start  543 end  548 total  556           clock  59.82Hz
  800x600 (0x1c5) 40.000MHz +HSync +VSync *current
        h: width   800 start  840 end  968 total 1056 skew    0 clock  37.88KHz
        v: height  600 start  601 end  605 total  628           clock  60.32Hz
  800x600 (0x1c6) 36.000MHz +HSync +VSync
        h: width   800 start  824 end  896 total 1024 skew    0 clock  35.16KHz
        v: height  600 start  601 end  603 total  625           clock  56.25Hz
  864x486 (0x1c7) 32.500MHz -HSync +VSync
        h: width   864 start  888 end  968 total 1072 skew    0 clock  30.32KHz
        v: height  486 start  489 end  494 total  506           clock  59.92Hz
  864x486 (0x1c8) 30.500MHz +HSync -VSync
        h: width   864 start  912 end  944 total 1024 skew    0 clock  29.79KHz
        v: height  486 start  489 end  494 total  500           clock  59.57Hz
  848x480 (0x1c9) 33.750MHz +HSync +VSync
        h: width   848 start  864 end  976 total 1088 skew    0 clock  31.02KHz
        v: height  480 start  486 end  494 total  517           clock  60.00Hz
  640x480 (0x1ca) 25.175MHz -HSync -VSync
        h: width   640 start  656 end  752 total  800 skew    0 clock  31.47KHz
        v: height  480 start  490 end  492 total  525           clock  59.94Hz
  720x405 (0x1cb) 22.500MHz -HSync +VSync
        h: width   720 start  744 end  808 total  896 skew    0 clock  25.11KHz
        v: height  405 start  408 end  413 total  422           clock  59.51Hz
  720x405 (0x1cc) 21.750MHz +HSync -VSync
        h: width   720 start  768 end  800 total  880 skew    0 clock  24.72KHz
        v: height  405 start  408 end  413 total  419           clock  58.99Hz
  640x360 (0x1cd) 18.000MHz -HSync +VSync
        h: width   640 start  664 end  720 total  800 skew    0 clock  22.50KHz
        v: height  360 start  363 end  368 total  376           clock  59.84Hz
  640x360 (0x1ce) 17.750MHz +HSync -VSync
        h: width   640 start  688 end  720 total  800 skew    0 clock  22.19KHz
        v: height  360 start  363 end  368 total  374           clock  59.32Hz
DP1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x44
   Timestamp:  410126
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
DP2 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x45
   Timestamp:  410126
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   Colorspace: Default
      supported: Default, RGB_Wide_Gamut_Fixed_Point, RGB_Wide_Gamut_Floating_Point, opRGB, DCI-P3_RGB_D65, BT2020_RGB, BT601_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, BT2020_CYCC, BT2020_YCC
   max bpc: 12
      range: (6, 12)
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
HDMI1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x46
   Timestamp:  410126
   Subpixel:   unknown
   Clones:   
   CRTCs:      0 1 2
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   HDCP Content Type: HDCP Type0
      supported: HDCP Type0, HDCP Type1
   Content Protection: Undesired
      supported: Undesired, Desired, Enabled
   max bpc: 12
      range: (8, 12)
   content type: No Data
      supported: No Data, Graphics, Photo, Cinema, Game
   Colorspace: Default
      supported: Default, SMPTE_170M_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, opRGB, BT2020_CYCC, BT2020_RGB, BT2020_YCC, DCI-P3_RGB_D65, DCI-P3_RGB_Theater
   aspect ratio: Automatic
      supported: Automatic, 4:3, 16:9
   Broadcast RGB: Automatic
      supported: Automatic, Full, Limited 16:235
   audio: auto
      supported: force-dvi, off, auto, on
   link-status: Good
      supported: Good, Bad
   non-desktop: 0
      range: (0, 1)
VIRTUAL1 disconnected (normal left inverted right x axis y axis)
   Identifier: 0x47
   Timestamp:  410126
   Subpixel:   no subpixels
   Clones:   
   CRTCs:      3
   Transform:  1.000000 0.000000 0.000000
               0.000000 1.000000 0.000000
               0.000000 0.000000 1.000000
              filter:
   non-desktop: 0
      supported: 0, 1



Code: Select all
journalctl -ab|grep xfce
Sep 16 17:27:22 introvertx95.extrovertdomain systemd[3474]: Not generating service for XDG autostart app-xfce4\x2dclipman\x2dplugin\x2dautostart-autostart.service, it is hidden.
Sep 16 17:27:22 introvertx95.extrovertdomain systemd[3474]: Not generating service for XDG autostart app-xfce4\x2dnotes\x2dautostart-autostart.service, it is hidden.
Sep 16 17:31:11 introvertx95.extrovertdomain systemd[19663]: Not generating service for XDG autostart app-xfce4\x2dclipman\x2dplugin\x2dautostart-autostart.service, it is hidden.
Sep 16 17:31:11 introvertx95.extrovertdomain systemd[19663]: Not generating service for XDG autostart app-xfce4\x2dnotes\x2dautostart-autostart.service, it is hidden.
Sep 16 17:31:11 introvertx95.extrovertdomain sddm-helper[19653]: Starting: "/usr/share/sddm/scripts/Xsession \"startxfce4\""
Sep 16 17:31:12 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Activating service name='org.xfce.Xfconf' requested by ':1.9' (uid=1000 pid=19671 comm="xfce4-session")
Sep 16 17:31:12 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Successfully activated service 'org.xfce.Xfconf'
Sep 16 17:31:12 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Activating service name='org.xfce.ScreenSaver' requested by ':1.9' (uid=1000 pid=19671 comm="xfce4-session")
Sep 16 17:31:12 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Successfully activated service 'org.xfce.ScreenSaver'
Sep 16 17:31:14 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Activating service name='org.freedesktop.Notifications' requested by ':1.89' (uid=1000 pid=20152 comm="xfce4-power-manager --restart --sm-client-id 2998a")
Sep 16 17:33:40 introvertx95.extrovertdomain unknown[19864]: xfce4-screensaver: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.
Sep 16 17:33:42 introvertx95.extrovertdomain systemd[28598]: Not generating service for XDG autostart app-xfce4\x2dclipman\x2dplugin\x2dautostart-autostart.service, it is hidden.
Sep 16 17:33:42 introvertx95.extrovertdomain systemd[28598]: Not generating service for XDG autostart app-xfce4\x2dnotes\x2dautostart-autostart.service, it is hidden.
Sep 16 17:33:48 introvertx95.extrovertdomain sddm-helper[28621]: Starting: "/usr/share/sddm/scripts/Xsession \"startxfce4\""
Sep 16 17:33:48 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Activating service name='org.xfce.ScreenSaver' requested by ':1.143' (uid=1000 pid=28626 comm="xfce4-session")
Sep 16 17:33:48 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Successfully activated service 'org.xfce.ScreenSaver'
Sep 16 17:34:02 introvertx95.extrovertdomain dbus-daemon[19698]: [session uid=1000 pid=19698] Activating service name='org.freedesktop.Notifications' requested by ':1.255' (uid=1000 pid=30085 comm="/usr/lib64/xfce4/panel/wrapper-2.0 /usr/lib64/xfce")



Code: Select all
[   403.400] (--) Log file renamed from "/var/log/Xorg.pid-28566.log" to "/var/log/Xorg.0.log"
[   403.401]
X.Org X Server 1.20.9
X Protocol Version 11, Revision 0
[   403.402] Build Operating System: rabbit 5.6.8-server-1.mga7
[   403.402] Current Operating System: Linux introvertx95.extrovertdomain 5.8.9-1.mga8custom #1 SMP Sun Sep 13 17:02:49 JST 2020 x86_64
[   403.402] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.8.9-1.mga8custom root=UUID=3c57e7de-134c-40de-be98-1be97d94fcab ro " drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0"
[   403.402] Build Date: 26 August 2020  07:12:27AM
[   403.402] Build ID: x11-server 1.20.9-7.mga8
[   403.402] Current version of pixman: 0.40.0
[   403.402]    Before reporting problems, check https://bugs.mageia.org
   to make sure that you have the latest version.
[   403.402] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   403.402] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Sep 16 17:33:42 2020
[   403.402] (==) Using config directory: "/etc/X11/xorg.conf.d"
[   403.402] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[   403.403] (==) No Layout section.  Using the first Screen section.
[   403.403] (==) No screen section available. Using defaults.
[   403.403] (**) |-->Screen "Default Screen Section" (0)
[   403.403] (**) |   |-->Monitor "<default monitor>"
[   403.403] (==) No monitor specified for screen "Default Screen Section".
   Using a default monitor configuration.
[   403.403] (==) Automatically adding devices
[   403.403] (==) Automatically enabling devices
[   403.403] (==) Automatically adding GPU devices
[   403.403] (==) Automatically binding GPU devices
[   403.403] (==) Max clients allowed: 256, resource mask: 0x1fffff
[   403.403] (==) FontPath set to:
   catalogue:/etc/X11/fontpath.d,
   built-ins
[   403.403] (**) ModulePath set to "/usr/lib64/xorg/extra-modules,/usr/lib64/xorg/modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[   403.403] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[   403.404] (II) Loader magic: 0x61fd40
[   403.404] (II) Module ABI versions:
[   403.404]    X.Org ANSI C Emulation: 0.4
[   403.404]    X.Org Video Driver: 24.1
[   403.404]    X.Org XInput driver : 24.1
[   403.404]    X.Org Server Extension : 10.0
[   403.405] (++) using VT number 1

[   403.405] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[   403.406] (II) xfree86: Adding drm device (/dev/dri/card0)
[   403.406] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card0
[   403.428] (--) PCI:*(0@0:2:0) 8086:8a52:8086:2212 rev 7, Mem @ 0x601c000000/16777216, 0x4000000000/268435456, I/O @ 0x00004000/64, BIOS @ 0x????????/131072
[   403.428] (II) Open ACPI successful (/var/run/acpid.socket)
[   403.428] (II) LoadModule: "glx"
[   403.429] (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so
[   403.431] (II) Module glx: vendor="X.Org Foundation"
[   403.431]    compiled for 1.20.9, module version = 1.0.0
[   403.431]    ABI class: X.Org Server Extension, version 10.0
[   403.431] (==) Matched intel as autoconfigured driver 0
[   403.431] (==) Matched modesetting as autoconfigured driver 1
[   403.431] (==) Matched fbdev as autoconfigured driver 2
[   403.431] (==) Matched vesa as autoconfigured driver 3
[   403.431] (==) Assigned the driver to the xf86ConfigLayout
[   403.431] (II) LoadModule: "intel"
[   403.431] (II) Loading /usr/lib64/xorg/modules/drivers/intel_drv.so
[   403.431] (II) Module intel: vendor="X.Org Foundation"
[   403.431]    compiled for 1.20.8, module version = 2.99.917
[   403.431]    Module class: X.Org Video Driver
[   403.431]    ABI class: X.Org Video Driver, version 24.1
[   403.431] (II) LoadModule: "modesetting"
[   403.431] (II) Loading /usr/lib64/xorg/modules/drivers/modesetting_drv.so
[   403.432] (II) Module modesetting: vendor="X.Org Foundation"
[   403.432]    compiled for 1.20.9, module version = 1.20.9
[   403.432]    Module class: X.Org Video Driver
[   403.432]    ABI class: X.Org Video Driver, version 24.1
[   403.432] (II) LoadModule: "fbdev"
[   403.432] (II) Loading /usr/lib64/xorg/modules/drivers/fbdev_drv.so
[   403.432] (II) Module fbdev: vendor="X.Org Foundation"
[   403.432]    compiled for 1.20.7, module version = 0.5.0
[   403.432]    Module class: X.Org Video Driver
[   403.432]    ABI class: X.Org Video Driver, version 24.1
[   403.432] (II) LoadModule: "vesa"
[   403.432] (II) Loading /usr/lib64/xorg/modules/drivers/vesa_drv.so
[   403.432] (II) Module vesa: vendor="X.Org Foundation"
[   403.432]    compiled for 1.20.7, module version = 2.4.0
[   403.432]    Module class: X.Org Video Driver
[   403.432]    ABI class: X.Org Video Driver, version 24.1
[   403.432] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
   i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
   915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
   Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
   GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[   403.433] (II) intel: Driver for Intel(R) HD Graphics
[   403.433] (II) intel: Driver for Intel(R) Iris(TM) Graphics
[   403.433] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics
[   403.433] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[   403.433] (II) FBDEV: driver for framebuffer: fbdev
[   403.433] (II) VESA: driver for VESA chipsets: vesa
[   403.433] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20200515
[   403.446] (WW) Falling back to old probe method for modesetting
[   403.447] (WW) Falling back to old probe method for fbdev
[   403.447] (II) Loading sub module "fbdevhw"
[   403.447] (II) LoadModule: "fbdevhw"
[   403.447] (II) Loading /usr/lib64/xorg/modules/libfbdevhw.so
[   403.448] (II) Module fbdevhw: vendor="X.Org Foundation"
[   403.448]    compiled for 1.20.9, module version = 0.0.2
[   403.448]    ABI class: X.Org Video Driver, version 24.1
[   403.448] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics
[   403.448] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2; using a maximum of 4 threads
[   403.449] (II) intel(0): Creating default Display subsection in Screen section
   "Default Screen Section" for depth/fbbpp 24/32
[   403.449] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[   403.449] (==) intel(0): RGB weight 888
[   403.449] (==) intel(0): Default visual is TrueColor
[   403.450] (II) intel(0): Output eDP1 has no monitor section
[   403.451] (**) intel(0): Found backlight control interface intel_backlight (type 'raw') for output eDP1
[   403.451] (II) intel(0): Enabled output eDP1
[   403.451] (II) intel(0): Output HDMI1 has no monitor section
[   403.451] (II) intel(0): Enabled output HDMI1
[   403.451] (II) intel(0): Output DP1 has no monitor section
[   403.451] (II) intel(0): Enabled output DP1
[   403.451] (II) intel(0): Output DP2 has no monitor section
[   403.452] (II) intel(0): Enabled output DP2
[   403.452] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[   403.452] (II) intel(0): Output VIRTUAL1 has no monitor section
[   403.452] (II) intel(0): Enabled output VIRTUAL1
[   403.452] (--) intel(0): Output eDP1 using initial mode 1024x768 on pipe 0
[   403.452] (==) intel(0): TearFree enabled
[   403.452] (==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
[   403.452] (==) intel(0): DPI set to (96, 96)
[   403.452] (II) Loading sub module "dri3"
[   403.452] (II) LoadModule: "dri3"
[   403.452] (II) Module "dri3" already built-in
[   403.452] (II) Loading sub module "dri2"
[   403.452] (II) LoadModule: "dri2"
[   403.452] (II) Module "dri2" already built-in
[   403.452] (II) Loading sub module "present"
[   403.452] (II) LoadModule: "present"
[   403.452] (II) Module "present" already built-in
[   403.453] (II) UnloadModule: "modesetting"
[   403.453] (II) Unloading modesetting
[   403.453] (II) UnloadModule: "fbdev"
[   403.453] (II) Unloading fbdev
[   403.453] (II) UnloadSubModule: "fbdevhw"
[   403.453] (II) Unloading fbdevhw
[   403.453] (II) UnloadModule: "vesa"
[   403.453] (II) Unloading vesa
[   403.454] (II) intel(0): SNA initialized with Skylake (gen9) backend
[   403.454] (==) intel(0): Backing store enabled
[   403.454] (==) intel(0): Silken mouse enabled
[   403.454] (II) intel(0): HW Cursor enabled
[   403.454] (==) intel(0): DPMS enabled
[   403.455] (==) intel(0): Display hotplug detection enabled
[   403.455] (II) intel(0): [DRI2] Setup complete
[   403.455] (II) intel(0): [DRI2]   DRI driver: i965
[   403.455] (II) intel(0): [DRI2]   VDPAU driver: va_gl
[   403.455] (II) intel(0): direct rendering: DRI2 DRI3 enabled
[   403.455] (II) intel(0): hardware support for Present enabled
[   403.455] (II) Initializing extension Generic Event Extension
[   403.455] (II) Initializing extension SHAPE
[   403.455] (II) Initializing extension MIT-SHM
[   403.456] (II) Initializing extension XInputExtension
[   403.456] (II) Initializing extension XTEST
[   403.456] (II) Initializing extension BIG-REQUESTS
[   403.456] (II) Initializing extension SYNC
[   403.456] (II) Initializing extension XKEYBOARD
[   403.457] (II) Initializing extension XC-MISC
[   403.457] (II) Initializing extension SECURITY
[   403.457] (II) Initializing extension XFIXES
[   403.457] (II) Initializing extension RENDER
[   403.457] (II) Initializing extension RANDR
[   403.458] (II) Initializing extension COMPOSITE
[   403.458] (II) Initializing extension DAMAGE
[   403.458] (II) Initializing extension MIT-SCREEN-SAVER
[   403.458] (II) Initializing extension DOUBLE-BUFFER
[   403.458] (II) Initializing extension RECORD
[   403.458] (II) Initializing extension DPMS
[   403.459] (II) Initializing extension Present
[   403.459] (II) Initializing extension DRI3
[   403.459] (II) Initializing extension X-Resource
[   403.459] (II) Initializing extension XVideo
[   403.459] (II) Initializing extension XVideo-MotionCompensation
[   403.459] (II) Initializing extension GLX
[   403.466] (II) AIGLX: Loaded and initialized i965
[   403.466] (II) GLX: Initialized DRI2 GL provider for screen 0
[   403.466] (II) Initializing extension XFree86-VidModeExtension
[   403.466] (II) Initializing extension XFree86-DGA
[   403.466] (II) Initializing extension XFree86-DRI
[   403.466] (II) Initializing extension DRI2
[   403.467] (II) intel(0): switch to mode 1024x768@60.0 on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[   403.469] (II) intel(0): Setting screen physical size to 270 x 203
[   403.489] (II) config/udev: Adding input device Power Button (/dev/input/event11)
[   403.489] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[   403.489] (**) Power Button: Applying InputClass "system-keyboard"
[   403.489] (II) LoadModule: "libinput"
[   403.489] (II) Loading /usr/lib64/xorg/modules/input/libinput_drv.so
[   403.490] (II) Module libinput: vendor="X.Org Foundation"
[   403.490]    compiled for 1.20.8, module version = 0.30.0
[   403.490]    Module class: X.Org XInput Driver
[   403.490]    ABI class: X.Org XInput driver, version 24.1
[   403.490] (II) Using input driver 'libinput' for 'Power Button'
[   403.490] (**) Power Button: always reports core events
[   403.490] (**) Option "Device" "/dev/input/event11"
[   403.490] (**) Option "_source" "server/udev"
[   403.491] (II) event11 - Power Button: is tagged by udev as: Keyboard
[   403.491] (II) event11 - Power Button: device is a keyboard
[   403.491] (II) event11 - Power Button: device removed
[   403.500] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input11/event11"
[   403.500] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[   403.500] (**) Option "xkb_model" "pc105"
[   403.500] (**) Option "xkb_layout" "us"
[   403.500] (**) Option "xkb_options" "compose:rwin"
[   403.512] (II) event11 - Power Button: is tagged by udev as: Keyboard
[   403.512] (II) event11 - Power Button: device is a keyboard
[   403.513] (II) config/udev: Adding input device Video Bus (/dev/input/event1)
[   403.513] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[   403.513] (**) Video Bus: Applying InputClass "system-keyboard"
[   403.513] (II) Using input driver 'libinput' for 'Video Bus'
[   403.513] (**) Video Bus: always reports core events
[   403.513] (**) Option "Device" "/dev/input/event1"
[   403.513] (**) Option "_source" "server/udev"
[   403.513] (II) event1  - Video Bus: is tagged by udev as: Keyboard
[   403.513] (II) event1  - Video Bus: device is a keyboard
[   403.513] (II) event1  - Video Bus: device removed
[   403.520] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input1/event1"
[   403.520] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[   403.520] (**) Option "xkb_model" "pc105"
[   403.520] (**) Option "xkb_layout" "us"
[   403.520] (**) Option "xkb_options" "compose:rwin"
[   403.521] (II) event1  - Video Bus: is tagged by udev as: Keyboard
[   403.521] (II) event1  - Video Bus: device is a keyboard
[   403.522] (II) config/udev: Adding input device Lid Switch (/dev/input/event8)
[   403.522] (II) No input driver specified, ignoring this device.
[   403.522] (II) This device may have been added with another device file.
[   403.522] (II) config/udev: Adding input device Power Button (/dev/input/event10)
[   403.522] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[   403.522] (**) Power Button: Applying InputClass "system-keyboard"
[   403.522] (II) Using input driver 'libinput' for 'Power Button'
[   403.522] (**) Power Button: always reports core events
[   403.522] (**) Option "Device" "/dev/input/event10"
[   403.522] (**) Option "_source" "server/udev"
[   403.523] (II) event10 - Power Button: is tagged by udev as: Keyboard
[   403.523] (II) event10 - Power Button: device is a keyboard
[   403.524] (II) event10 - Power Button: device removed
[   403.532] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input10/event10"
[   403.532] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[   403.532] (**) Option "xkb_model" "pc105"
[   403.532] (**) Option "xkb_layout" "us"
[   403.532] (**) Option "xkb_options" "compose:rwin"
[   403.533] (II) event10 - Power Button: is tagged by udev as: Keyboard
[   403.534] (II) event10 - Power Button: device is a keyboard
[   403.534] (II) config/udev: Adding input device Sleep Button (/dev/input/event9)
[   403.534] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[   403.535] (**) Sleep Button: Applying InputClass "system-keyboard"
[   403.535] (II) Using input driver 'libinput' for 'Sleep Button'
[   403.535] (**) Sleep Button: always reports core events
[   403.535] (**) Option "Device" "/dev/input/event9"
[   403.535] (**) Option "_source" "server/udev"
[   403.536] (II) event9  - Sleep Button: is tagged by udev as: Keyboard
[   403.536] (II) event9  - Sleep Button: device is a keyboard
[   403.536] (II) event9  - Sleep Button: device removed
[   403.544] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input9/event9"
[   403.544] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[   403.544] (**) Option "xkb_model" "pc105"
[   403.544] (**) Option "xkb_layout" "us"
[   403.544] (**) Option "xkb_options" "compose:rwin"
[   403.546] (II) event9  - Sleep Button: is tagged by udev as: Keyboard
[   403.546] (II) event9  - Sleep Button: device is a keyboard
[   403.548] (II) config/udev: Adding input device HID 6901:2701 (/dev/input/event2)
[   403.548] (**) HID 6901:2701: Applying InputClass "libinput keyboard catchall"
[   403.548] (**) HID 6901:2701: Applying InputClass "system-keyboard"
[   403.548] (II) Using input driver 'libinput' for 'HID 6901:2701'
[   403.548] (**) HID 6901:2701: always reports core events
[   403.548] (**) Option "Device" "/dev/input/event2"
[   403.548] (**) Option "_source" "server/udev"
[   403.550] (II) event2  - HID 6901:2701: is tagged by udev as: Keyboard
[   403.550] (II) event2  - HID 6901:2701: device is a keyboard
[   403.551] (II) event2  - HID 6901:2701: device removed
[   403.560] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.0/0003:6901:2701.0001/input/input2/event2"
[   403.560] (II) XINPUT: Adding extended input device "HID 6901:2701" (type: KEYBOARD, id 10)
[   403.560] (**) Option "xkb_model" "pc105"
[   403.560] (**) Option "xkb_layout" "us"
[   403.560] (**) Option "xkb_options" "compose:rwin"
[   403.563] (II) event2  - HID 6901:2701: is tagged by udev as: Keyboard
[   403.563] (II) event2  - HID 6901:2701: device is a keyboard
[   403.565] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/event3)
[   403.565] (**) HID 6901:2701 Mouse: Applying InputClass "libinput pointer catchall"
[   403.565] (II) Using input driver 'libinput' for 'HID 6901:2701 Mouse'
[   403.565] (**) HID 6901:2701 Mouse: always reports core events
[   403.565] (**) Option "Device" "/dev/input/event3"
[   403.565] (**) Option "_source" "server/udev"
[   403.567] (II) event3  - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[   403.567] (II) event3  - HID 6901:2701 Mouse: device is a pointer
[   403.568] (II) event3  - HID 6901:2701 Mouse: device removed
[   403.584] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input3/event3"
[   403.584] (II) XINPUT: Adding extended input device "HID 6901:2701 Mouse" (type: MOUSE, id 11)
[   403.585] (**) Option "AccelerationScheme" "none"
[   403.585] (**) HID 6901:2701 Mouse: (accel) selected scheme none/0
[   403.585] (**) HID 6901:2701 Mouse: (accel) acceleration factor: 2.000
[   403.585] (**) HID 6901:2701 Mouse: (accel) acceleration threshold: 4
[   403.590] (II) event3  - HID 6901:2701 Mouse: is tagged by udev as: Mouse
[   403.590] (II) event3  - HID 6901:2701 Mouse: device is a pointer
[   403.592] (II) config/udev: Adding input device HID 6901:2701 Mouse (/dev/input/mouse0)
[   403.592] (II) No input driver specified, ignoring this device.
[   403.592] (II) This device may have been added with another device file.
[   403.593] (II) config/udev: Adding input device HID 6901:2701 Consumer Control (/dev/input/event4)
[   403.593] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[   403.593] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[   403.594] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[   403.594] (**) HID 6901:2701 Consumer Control: always reports core events
[   403.594] (**) Option "Device" "/dev/input/event4"
[   403.594] (**) Option "_source" "server/udev"
[   403.596] (II) event4  - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[   403.596] (II) event4  - HID 6901:2701 Consumer Control: device is a keyboard
[   403.596] (II) event4  - HID 6901:2701 Consumer Control: device removed
[   403.605] (II) libinput: HID 6901:2701 Consumer Control: needs a virtual subdevice
[   403.605] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[   403.605] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: MOUSE, id 12)
[   403.605] (**) Option "AccelerationScheme" "none"
[   403.605] (**) HID 6901:2701 Consumer Control: (accel) selected scheme none/0
[   403.605] (**) HID 6901:2701 Consumer Control: (accel) acceleration factor: 2.000
[   403.605] (**) HID 6901:2701 Consumer Control: (accel) acceleration threshold: 4
[   403.609] (II) event4  - HID 6901:2701 Consumer Control: is tagged by udev as: Keyboard
[   403.609] (II) event4  - HID 6901:2701 Consumer Control: device is a keyboard
[   403.610] (II) config/udev: Adding input device HID 6901:2701 System Control (/dev/input/event5)
[   403.610] (**) HID 6901:2701 System Control: Applying InputClass "libinput keyboard catchall"
[   403.610] (**) HID 6901:2701 System Control: Applying InputClass "system-keyboard"
[   403.610] (II) Using input driver 'libinput' for 'HID 6901:2701 System Control'
[   403.610] (**) HID 6901:2701 System Control: always reports core events
[   403.610] (**) Option "Device" "/dev/input/event5"
[   403.610] (**) Option "_source" "server/udev"
[   403.612] (II) event5  - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[   403.613] (II) event5  - HID 6901:2701 System Control: device is a keyboard
[   403.613] (II) event5  - HID 6901:2701 System Control: device removed
[   403.621] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input5/event5"
[   403.621] (II) XINPUT: Adding extended input device "HID 6901:2701 System Control" (type: KEYBOARD, id 13)
[   403.621] (**) Option "xkb_model" "pc105"
[   403.621] (**) Option "xkb_layout" "us"
[   403.621] (**) Option "xkb_options" "compose:rwin"
[   403.624] (II) event5  - HID 6901:2701 System Control: is tagged by udev as: Keyboard
[   403.625] (II) event5  - HID 6901:2701 System Control: device is a keyboard
[   403.626] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/event6)
[   403.626] (**)   Mouse for Windows: Applying InputClass "libinput pointer catchall"
[   403.626] (II) Using input driver 'libinput' for '  Mouse for Windows'
[   403.626] (**)   Mouse for Windows: always reports core events
[   403.626] (**) Option "Device" "/dev/input/event6"
[   403.626] (**) Option "_source" "server/udev"
[   403.628] (II) event6  -   Mouse for Windows: is tagged by udev as: Mouse
[   403.628] (II) event6  -   Mouse for Windows: device is a pointer
[   403.628] (II) event6  -   Mouse for Windows: device removed
[   403.645] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.0/0003:2F24:0118.0003/input/input6/event6"
[   403.645] (II) XINPUT: Adding extended input device "  Mouse for Windows" (type: MOUSE, id 14)
[   403.645] (**) Option "AccelerationScheme" "none"
[   403.645] (**)   Mouse for Windows: (accel) selected scheme none/0
[   403.645] (**)   Mouse for Windows: (accel) acceleration factor: 2.000
[   403.645] (**)   Mouse for Windows: (accel) acceleration threshold: 4
[   403.650] (II) event6  -   Mouse for Windows: is tagged by udev as: Mouse
[   403.651] (II) event6  -   Mouse for Windows: device is a pointer
[   403.652] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/mouse1)
[   403.652] (II) No input driver specified, ignoring this device.
[   403.652] (II) This device may have been added with another device file.
[   403.654] (II) config/udev: Adding input device   Mouse for Windows (/dev/input/event7)
[   403.654] (**)   Mouse for Windows: Applying InputClass "libinput keyboard catchall"
[   403.654] (**)   Mouse for Windows: Applying InputClass "system-keyboard"
[   403.654] (II) Using input driver 'libinput' for '  Mouse for Windows'
[   403.654] (**)   Mouse for Windows: always reports core events
[   403.654] (**) Option "Device" "/dev/input/event7"
[   403.654] (**) Option "_source" "server/udev"
[   403.656] (II) event7  -   Mouse for Windows: is tagged by udev as: Keyboard
[   403.656] (II) event7  -   Mouse for Windows: device is a keyboard
[   403.657] (II) event7  -   Mouse for Windows: device removed
[   403.673] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-5/3-5:1.1/0003:2F24:0118.0004/input/input7/event7"
[   403.673] (II) XINPUT: Adding extended input device "  Mouse for Windows" (type: KEYBOARD, id 15)
[   403.673] (**) Option "xkb_model" "pc105"
[   403.673] (**) Option "xkb_layout" "us"
[   403.673] (**) Option "xkb_options" "compose:rwin"
[   403.679] (II) event7  -   Mouse for Windows: is tagged by udev as: Keyboard
[   403.679] (II) event7  -   Mouse for Windows: device is a keyboard
[   403.681] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/event14)
[   403.681] (**) HTIX5288:00 093A:0255 Mouse: Applying InputClass "libinput pointer catchall"
[   403.681] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Mouse'
[   403.681] (**) HTIX5288:00 093A:0255 Mouse: always reports core events
[   403.681] (**) Option "Device" "/dev/input/event14"
[   403.682] (**) Option "_source" "server/udev"
[   403.684] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[   403.685] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[   403.686] (II) event14 - HTIX5288:00 093A:0255 Mouse: device removed
[   403.705] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input17/event14"
[   403.705] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Mouse" (type: MOUSE, id 16)
[   403.705] (**) Option "AccelerationScheme" "none"
[   403.706] (**) HTIX5288:00 093A:0255 Mouse: (accel) selected scheme none/0
[   403.706] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration factor: 2.000
[   403.706] (**) HTIX5288:00 093A:0255 Mouse: (accel) acceleration threshold: 4
[   403.711] (II) event14 - HTIX5288:00 093A:0255 Mouse: is tagged by udev as: Mouse Pointingstick
[   403.712] (II) event14 - HTIX5288:00 093A:0255 Mouse: device is a pointer
[   403.716] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Mouse (/dev/input/mouse2)
[   403.716] (II) No input driver specified, ignoring this device.
[   403.716] (II) This device may have been added with another device file.
[   403.717] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/event15)
[   403.717] (**) HTIX5288:00 093A:0255 Touchpad: Applying InputClass "libinput touchpad catchall"
[   403.717] (II) Using input driver 'libinput' for 'HTIX5288:00 093A:0255 Touchpad'
[   403.717] (**) HTIX5288:00 093A:0255 Touchpad: always reports core events
[   403.717] (**) Option "Device" "/dev/input/event15"
[   403.717] (**) Option "_source" "server/udev"
[   403.719] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[   403.720] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[   403.721] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[   403.721] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device removed
[   403.742] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-12/i2c-HTIX5288:00/0018:093A:0255.0005/input/input18/event15"
[   403.742] (II) XINPUT: Adding extended input device "HTIX5288:00 093A:0255 Touchpad" (type: TOUCHPAD, id 17)
[   403.747] (**) Option "AccelerationScheme" "none"
[   403.747] (**) HTIX5288:00 093A:0255 Touchpad: (accel) selected scheme none/0
[   403.747] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration factor: 2.000
[   403.747] (**) HTIX5288:00 093A:0255 Touchpad: (accel) acceleration threshold: 4
[   403.751] (II) event15 - HTIX5288:00 093A:0255 Touchpad: is tagged by udev as: Touchpad
[   403.752] (EE) event15 - HTIX5288:00 093A:0255 Touchpad: kernel bug: clickpad advertising right button
[   403.754] (II) event15 - HTIX5288:00 093A:0255 Touchpad: device is a touchpad
[   403.755] (II) config/udev: Adding input device HTIX5288:00 093A:0255 Touchpad (/dev/input/mouse3)
[   403.755] (II) No input driver specified, ignoring this device.
[   403.755] (II) This device may have been added with another device file.
[   403.756] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/event16)
[   403.756] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[   403.756] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[   403.756] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[   403.756] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[   403.756] (**) Goodix Capacitive TouchScreen: always reports core events
[   403.756] (**) Option "Device" "/dev/input/event16"
[   403.756] (**) Option "_source" "server/udev"
[   403.757] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[   403.758] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[   403.758] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[   403.758] (II) event16 - Goodix Capacitive TouchScreen: device removed
[   403.777] (II) libinput: Goodix Capacitive TouchScreen: needs a virtual subdevice
[   403.777] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[   403.777] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: TOUCHSCREEN, id 18)
[   403.777] (**) Option "AccelerationScheme" "none"
[   403.778] (**) Goodix Capacitive TouchScreen: (accel) selected scheme none/0
[   403.778] (**) Goodix Capacitive TouchScreen: (accel) acceleration factor: 2.000
[   403.778] (**) Goodix Capacitive TouchScreen: (accel) acceleration threshold: 4
[   403.782] (II) event16 - Goodix Capacitive TouchScreen: is tagged by udev as: Keyboard Touchscreen
[   403.783] (II) event16 - Goodix Capacitive TouchScreen: device is a keyboard
[   403.783] (II) event16 - Goodix Capacitive TouchScreen: device is a touch device
[   403.785] (II) config/udev: Adding input device Goodix Capacitive TouchScreen (/dev/input/mouse4)
[   403.785] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[   403.785] (II) No input driver specified, ignoring this device.
[   403.785] (II) This device may have been added with another device file.
[   403.787] (II) config/udev: Adding input device Intel HID events (/dev/input/event12)
[   403.787] (**) Intel HID events: Applying InputClass "libinput keyboard catchall"
[   403.787] (**) Intel HID events: Applying InputClass "system-keyboard"
[   403.787] (II) Using input driver 'libinput' for 'Intel HID events'
[   403.787] (**) Intel HID events: always reports core events
[   403.787] (**) Option "Device" "/dev/input/event12"
[   403.787] (**) Option "_source" "server/udev"
[   403.788] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[   403.789] (II) event12 - Intel HID events: device is a keyboard
[   403.789] (II) event12 - Intel HID events: device removed
[   403.801] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input12/event12"
[   403.801] (II) XINPUT: Adding extended input device "Intel HID events" (type: KEYBOARD, id 19)
[   403.801] (**) Option "xkb_model" "pc105"
[   403.801] (**) Option "xkb_layout" "us"
[   403.801] (**) Option "xkb_options" "compose:rwin"
[   403.805] (II) event12 - Intel HID events: is tagged by udev as: Keyboard
[   403.805] (II) event12 - Intel HID events: device is a keyboard
[   403.807] (II) config/udev: Adding input device Intel HID 5 button array (/dev/input/event13)
[   403.807] (**) Intel HID 5 button array: Applying InputClass "libinput keyboard catchall"
[   403.807] (**) Intel HID 5 button array: Applying InputClass "system-keyboard"
[   403.807] (II) Using input driver 'libinput' for 'Intel HID 5 button array'
[   403.807] (**) Intel HID 5 button array: always reports core events
[   403.807] (**) Option "Device" "/dev/input/event13"
[   403.807] (**) Option "_source" "server/udev"
[   403.809] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[   403.809] (II) event13 - Intel HID 5 button array: device is a keyboard
[   403.810] (II) event13 - Intel HID 5 button array: device removed
[   403.818] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D5:00/input/input13/event13"
[   403.818] (II) XINPUT: Adding extended input device "Intel HID 5 button array" (type: KEYBOARD, id 20)
[   403.818] (**) Option "xkb_model" "pc105"
[   403.818] (**) Option "xkb_layout" "us"
[   403.818] (**) Option "xkb_options" "compose:rwin"
[   403.821] (II) event13 - Intel HID 5 button array: is tagged by udev as: Keyboard
[   403.822] (II) event13 - Intel HID 5 button array: device is a keyboard
[   403.823] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event17)
[   403.823] (II) No input driver specified, ignoring this device.
[   403.823] (II) This device may have been added with another device file.
[   403.824] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event18)
[   403.824] (II) No input driver specified, ignoring this device.
[   403.824] (II) This device may have been added with another device file.
[   403.824] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event19)
[   403.824] (II) No input driver specified, ignoring this device.
[   403.824] (II) This device may have been added with another device file.
[   403.825] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event20)
[   403.825] (II) No input driver specified, ignoring this device.
[   403.825] (II) This device may have been added with another device file.
[   403.826] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event21)
[   403.826] (II) No input driver specified, ignoring this device.
[   403.826] (II) This device may have been added with another device file.
[   403.826] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event22)
[   403.826] (II) No input driver specified, ignoring this device.
[   403.826] (II) This device may have been added with another device file.
[   403.827] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=10 (/dev/input/event23)
[   403.827] (II) No input driver specified, ignoring this device.
[   403.827] (II) This device may have been added with another device file.
[   403.827] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=11 (/dev/input/event24)
[   403.827] (II) No input driver specified, ignoring this device.
[   403.827] (II) This device may have been added with another device file.
[   403.827] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=12 (/dev/input/event25)
[   403.827] (II) No input driver specified, ignoring this device.
[   403.827] (II) This device may have been added with another device file.
[   403.828] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[   403.828] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[   403.828] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[   403.828] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[   403.828] (**) AT Translated Set 2 keyboard: always reports core events
[   403.828] (**) Option "Device" "/dev/input/event0"
[   403.828] (**) Option "_source" "server/udev"
[   403.829] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[   403.829] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[   403.831] (II) event0  - AT Translated Set 2 keyboard: device removed
[   403.842] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[   403.842] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 21)
[   403.842] (**) Option "xkb_model" "pc105"
[   403.842] (**) Option "xkb_layout" "us"
[   403.842] (**) Option "xkb_options" "compose:rwin"
[   403.844] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[   403.845] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[   403.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "libinput keyboard catchall"
[   403.888] (**) HID 6901:2701 Consumer Control: Applying InputClass "system-keyboard"
[   403.888] (II) Using input driver 'libinput' for 'HID 6901:2701 Consumer Control'
[   403.888] (**) HID 6901:2701 Consumer Control: always reports core events
[   403.888] (**) Option "Device" "/dev/input/event4"
[   403.888] (**) Option "_source" "_driver/libinput"
[   403.888] (II) libinput: HID 6901:2701 Consumer Control: is a virtual subdevice
[   403.888] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-2/3-2:1.1/0003:6901:2701.0002/input/input4/event4"
[   403.888] (II) XINPUT: Adding extended input device "HID 6901:2701 Consumer Control" (type: KEYBOARD, id 22)
[   403.888] (**) Option "xkb_model" "pc105"
[   403.888] (**) Option "xkb_layout" "us"
[   403.888] (**) Option "xkb_options" "compose:rwin"
[   403.889] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput keyboard catchall"
[   403.889] (**) Goodix Capacitive TouchScreen: Applying InputClass "libinput touchscreen catchall"
[   403.889] (**) Goodix Capacitive TouchScreen: Applying InputClass "system-keyboard"
[   403.889] (II) Using input driver 'libinput' for 'Goodix Capacitive TouchScreen'
[   403.889] (**) Goodix Capacitive TouchScreen: always reports core events
[   403.889] (**) Option "Device" "/dev/input/event16"
[   403.889] (**) Option "_source" "_driver/libinput"
[   403.889] (II) libinput: Goodix Capacitive TouchScreen: is a virtual subdevice
[   403.890] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-14/i2c-GDIX1002:00/input/input16/event16"
[   403.890] (II) XINPUT: Adding extended input device "Goodix Capacitive TouchScreen" (type: KEYBOARD, id 23)
[   403.890] (**) Option "xkb_model" "pc105"
[   403.890] (**) Option "xkb_layout" "us"
[   403.890] (**) Option "xkb_options" "compose:rwin"
[   403.894] (EE) Failed to open authorization file "/var/run/sddm/{0981c709-ab38-4527-af78-0050238eac3f}": No such file or directory
[   410.126] (II) intel(0): resizing framebuffer to 600x800
[   410.126] (II) intel(0): switch to mode 800x600@60.3 on eDP1 using pipe 0, position (0, 0), rotation right, reflection none
[   445.575] (EE) intel(0): Failed to submit rendering commands (Input/output error), disabling acceleration.
[   445.575] (EE) intel(0): When reporting this, please include /sys/class/drm/card0/error and the full dmesg.


Code: Select all
[   403.894] (EE) Failed to open authorization file "/var/run/sddm/{0981c709-ab38-4527-af78-0050238eac3f}": No such file or directory
[   410.126] (II) intel(0): resizing framebuffer to 600x800
[   410.126] (II) intel(0): switch to mode 800x600@60.3 on eDP1 using pipe 0, position (0, 0), rotation right, reflection none
[   445.575] (EE) intel(0): Failed to submit rendering commands (Input/output error), disabling acceleration.
[   445.575] (EE) intel(0): When reporting this, please include /sys/class/drm/card0/error and the full dmesg.
Last edited by doktor5000 on Sep 19th, '20, 16:10, edited 1 time in total.
Reason: remove duplicate / superfluous log output
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 16th, '20, 11:02

In Xfce... I had to reset X and login a 2nd time for it to start fully vs just hanging with a cursor on a black screen
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 16th, '20, 11:43

This is what I can find, I do not know if it's limited because I can only use the GUI here with the screen issue.

I was looking at what you wrote: CONFIG_DRM_KMS_HELPER needs to be enabled or as a module,

The thing is... it is not appearing here in the list.

https://www.kernelconfig.io/CONFIG_DRM_ ... ion=3.17.8

says it should be at:
Linux Kernel Configuration
└─> Device Drivers
└─> Graphics support
└─> Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)
└─> DRM_KMS_HELPER

https://www.kernelconfig.io/CONFIG_DRM_ ... ion=3.17.8

says it's called by this and this is here:

Linux Kernel Configuration
└─> Device Drivers
└─> Graphics support
└─> DRM_KMS_FB_HELPER


attached images indicate what I found there and enabled.

Are these missing or hidden because they should be on already? The 1st one is said not to be configurable in the link, CONFIG_DRM_KMS_HELPER

NOTE: It doesn't seem to honor my spacing with the arrows.
Attachments
Screenshot_2020-09-16_18-25-42.png
Screenshot_2020-09-16_18-25-42.png (96.5 KiB) Viewed 256 times
Screenshot_2020-09-16_18-23-42.png
Screenshot_2020-09-16_18-23-42.png (35.55 KiB) Viewed 256 times
Screenshot_2020-09-16_18-22-56.png
Screenshot_2020-09-16_18-22-56.png (58.79 KiB) Viewed 256 times
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 16th, '20, 11:58

connected to 1920x1080 projector via HDMI. Expanded the terminal window.

Tried: make menuconfig

to see if I could get the ncurses menu.

Code: Select all
make[1]: *** [scripts/kconfig/Makefile:29: menuconfig] Segmentation fault (core dumped)
                                                                                       make: *** [Makefile:606: menuconfig] Error 2
                                                                                                                                   [root@introvertx95 kernel-5


The result...
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 19th, '20, 10:23

Hello, did the logs or anything else here help in understanding what is taking place here and why the custom edid is not being used?

Is there another thing to be tried or should a possible bug report be filed for something unavailable?
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 19th, '20, 16:52

The kernelconfig link your asked about is for kernel 3.x which is pretty old information, we're at kernel 5.x now.
You can also read that during kernel configuration. If make menuconfig does not work for you, check if you have ncurses-devel packages installed.
Otherwise try with "make nconfig" or "make xconfig" for a Qt-based frontend or "make gconfig" for a GTK-based config frontend - although you might need to install some packages for that.

What you need enabled is CONFIG_DRM_LOAD_EDID_FIRMWARE and CONFIG_DRM_KMS_HELPER enabled or as a module, as already mentioned.
I can't comment on if any other kernel patch is necessary, maybe some DRM or intel driver-specific patches, you would need to figure that out yourself if you want to get your hardware working.


In any case, current EDID override does not seem to be used at all. What you could try is replace this

drm_kms_helper.edid_firmware=eDP1:edid/gpdwinmax.bin

with this, which seems to be the current way since kernel >=4.15.0 - Also as already mentioned, I'd leave out the output so remove the eDP1: part for now. You can add it later once it's working at all.

drm.edid_firmware=edid/gpdwinmax.bin

or additionally with video= like so:

video=eDP1:800x1200@60 drm.edid_firmware=edid/gpdwinmax.bin

Note that the name of the output is different then what xrandr shows. The name of the kernel output devices can be seen via e.g. ll /sys/class/drm/card*-*

Also the EDID file might be only read below /lib/firmware/edid and not under /usr/lib/firmware/edid/ so please check your /etc/dracut.conf.d/99-edid.conf again.
As your lsinitrd output lists the EDID file as usr/lib/firmware/edid/gpdwinmax.bin and not lib/firmware/edid/gpdwinmax.bin as expected.

I've found some example log output and when custom EDID is actually used, this is what it should look like in journalctl

[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-22-generic root=UUID=58fe8589-5cdf-47c1-b47a-2876215cd804 ro video=HDMI-A-1:1920x1080@50D drm.edid_firmware=HDMI-A-1:edid/edid.bin quiet splash vt.handoff=7
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-22-generic root=UUID=58fe8589-5cdf-47c1-b47a-2876215cd804 ro video=HDMI-A-1:1920x1080@50D drm.edid_firmware=HDMI-A-1:edid/edid.bin quiet splash vt.handoff=7
[ 1.838528] [drm] Memory usable by graphics device = 2048M
[ 1.838533] fb: switching to inteldrmfb from EFI VGA
[ 1.838670] [drm] Replacing VGA console driver
[ 1.844073] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.844074] [drm] Driver supports precise vblank timestamp query.
[ 1.847358] [drm] forcing HDMI-A-1 connector on
[ 1.850036] [drm] Got external EDID base block and 1 extension from "edid/edid.bin" for connector "HDMI-A-1"
[ 1.850318] [drm] Initialized i915 1.6.0 20171023 for 0000:00:02.0 on minor 0
[ 1.862212] [drm] Got external EDID base block and 1 extension from "edid/edid.bin" for connector "HDMI-A-1"
[ 1.875262] fbcon: inteldrmfb (fb0) is primary device
[ 1.875374] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.157254] [drm] Got external EDID base block and 1 extension from "edid/edid.bin" for connector "HDMI-A-1"
[ 3.274527] [drm] Got external EDID base block and 1 extension from "edid/edid.bin" for connector "HDMI-A-1"
[ 10.186864] [drm] Got external EDID base block and 1 extension from "edid/edid.bin" for connector "HDMI-A-1"


Please also post the output of
Code: Select all
ll /sys/module/drm_kms_helper/parameters/
ll /sys/class/drm
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 19th, '20, 18:22

I will post those... outputs as soon as possible.

I showed in the image what is available to be enabled and I enable it. I am using the xconfig and yes had to install something extra for that.

Previously I did show the original output from trying to rebuild the kernel the 1st time. It is here somewhere. It said then that my screen was too small. I can only at present use 800x600 screen which seems to be about half the screens size which is why I get 2 split screens.

I will have a check of the location of the firmware.bin file as you suggest. I typed the commands as you gave, in fact copy and pasted. As I recall they are in /lib/firmware/edid not /usr/lib/firmware/edid.

I will have a look at that closely.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 19th, '20, 19:02

the reason I sent the images as well as the link to the kernel org page, yes that is an old kernel but is there any reason you think the location should be other than described?

I sent a photo and the point was that in that photo of my use of the xconfig gui option...

I find no: CONFIG_DRM_KMS_HELPER

Perhaps I am looking in the wrong location. Can you kindly tell me where it is?
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 19th, '20, 20:03

I don't know what you're looking for on your screenshots. This is exactly in the place where the config says it should be:

-> Device Drivers
       -> Graphics support
         -> Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) (DRM [=m])
          -> Allow to specify an EDID data set instead of probing for it

The last one is not enabled in Mageia default kernel configuration and should be enabled.

This is an excerpt from search via ncurses config for kernel-5.7.19-desktop-1.mga7 :
Code: Select all
┌── Search Results ─────────────────────────────────────────────────────────────────────┐
│                                                                                       │
│ Symbol: DRM_LOAD_EDID_FIRMWARE [=n]                                                   │
│ Type  : bool                                                                          │
│ Defined at drivers/gpu/drm/Kconfig:154                                                │
│   Prompt: Allow to specify an EDID data set instead of probing for it                 │
│   Depends on: HAS_IOMEM [=y] && DRM [=m]                                              │
│   Location:                                                                           │
│     -> Device Drivers                                                                 │
│       -> Graphics support                                                             │
│         -> Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) (DRM [=m]) │
│                                                                                       │
│                                                                                       │
│ Symbol: FIRMWARE_EDID [=n]                                                            │
│ Type  : bool                                                                          │
│ Defined at drivers/video/fbdev/Kconfig:48                                             │
│   Prompt: Enable firmware EDID                                                        │
│   Depends on: HAS_IOMEM [=y] && FB [=y]                                               │
│   Location:                                                                           │
│     -> Device Drivers                                                                 │
│       -> Graphics support                                                             │
│         -> Frame buffer Devices                                                       │
│           -> Support for frame buffer devices (FB [=y])                               │



CONFIG_DRM_KMS_HELPER is not explicitly selectable, but implicitly enabled by other options:

Code: Select all
┌── Search Results ─────────────────────────────────────────────────────────────────────┐
│                                                                                       │
│ Symbol: DRM_KMS_HELPER [=m]                                                           │
│ Type  : tristate                                                                      │
│ Defined at drivers/gpu/drm/Kconfig:74                                                 │
│   Depends on: HAS_IOMEM [=y] && DRM [=m]                                              │
│ Selected by [m]:                                                                      │
│   - DRM_FBDEV_EMULATION [=y] && HAS_IOMEM [=y] && DRM [=m]                            │
│   - DRM_RADEON [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]             │
│   - DRM_AMDGPU [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]             │
│   - DRM_NOUVEAU [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]            │
│   - DRM_I915 [=m] && HAS_IOMEM [=y] && DRM [=m] && X86 [=y] && PCI [=y]               │
│   - DRM_VMWGFX [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && X86 [=y] && MMU [=y] │
│   - DRM_GMA500 [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && X86 [=y] && MMU [=y] │
│   - DRM_UDL [=m] && HAS_IOMEM [=y] && DRM [=m] && USB [=m] && USB_ARCH_HAS_HCD [=y]   │
│   - DRM_AST [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]                │
│   - DRM_MGAG200 [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]            │
│   - DRM_CIRRUS_QEMU [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]        │
│   - DRM_QXL [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]                │
│   - DRM_BOCHS [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && MMU [=y]              │
│   - DRM_VIRTIO_GPU [=m] && HAS_IOMEM [=y] && DRM [=m] && VIRTIO [=m] && MMU [=y]      │
│   - DRM_GM12U320 [=m] && HAS_IOMEM [=y] && DRM [=m] && USB [=m]                       │
│   - DRM_XEN_FRONTEND [=m] && HAS_IOMEM [=y] && DRM_XEN [=y] && DRM [=m]               │
│   - DRM_VBOXVIDEO [=m] && HAS_IOMEM [=y] && DRM [=m] && X86 [=y] && PCI [=y]          │
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 05:04

Very good, then it's enabled as it should be, that was in my question with the images, but perhaps my wording was incorrect.

Sabungayam wrote:
Are these missing or hidden because they should be on already? The 1st one is said not to be configurable in the link, CONFIG_DRM_KMS_HELPER



doktor5000 wrote:I don't know what you're looking for on your screenshots. This is exactly in the place where the config says it should be:


My mistake it wording, I thought I said clearly what I was looking for: CONFIG_DRM_KMS_HELPER

But now that you have clarified it, then I am aware that I have enabled what needs to be enabled after all. I do not generally mess with the kernel. I do not have the high level of understanding that you do.

So my questions may seem ridiculous or redundant. But then I do not know so asking is the only way to find out. Even just because I search and READ something on some forum does not mean I understand it.

So the point of my images was a concern that CONFIG_DRM_KMS_HELPER was not something I could find on the kernel config menu and that perhaps it was not fully enabled as you specified. As though I don't understand, some of the logs say things clearly like the edid isn't being used.

I have meetings today, I will see about getting you those command outputs when I can today.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 05:16

]ll /sys/module/drm_kms_helper/parameters/

Code: Select all
ll /sys/module/drm_kms_helper/parameters/
total 0
-rw-r--r-- 1 root root 4096 Sep 20 03:11 dp_aux_i2c_speed_khz
-rw-r--r-- 1 root root 4096 Sep 20 03:11 dp_aux_i2c_transfer_size
-rw------- 1 root root 4096 Sep 20 03:11 drm_dp_cec_unregister_delay
-r--r--r-- 1 root root 4096 Sep 20 03:11 drm_fbdev_overalloc
-rw-r--r-- 1 root root 4096 Sep 20 03:11 edid_firmware
-rw------- 1 root root 4096 Sep 20 03:11 fbdev_emulation
-rw------- 1 root root 4096 Sep 20 03:11 poll


ll /sys/class/drm

Code: Select all
ll /sys/class/drm
total 0
lrwxrwxrwx 1 root root    0 Sep 20  2020 card0 -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/
lrwxrwxrwx 1 root root    0 Sep 20  2020 card0-DP-1 -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-DP-1/
lrwxrwxrwx 1 root root    0 Sep 20  2020 card0-DP-2 -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-DP-2/
lrwxrwxrwx 1 root root    0 Sep 20  2020 card0-eDP-1 -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-eDP-1/
lrwxrwxrwx 1 root root    0 Sep 20  2020 card0-HDMI-A-1 -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-HDMI-A-1/
lrwxrwxrwx 1 root root    0 Sep 20  2020 renderD128 -> ../../devices/pci0000:00/0000:00:02.0/drm/renderD128/
-r--r--r-- 1 root root 4096 Sep 20  2020 version
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 05:37

Also the EDID file might be only read below /lib/firmware/edid and not under /usr/lib/firmware/edid/ so please check your /etc/dracut.conf.d/99-edid.conf again.
As your lsinitrd output lists the EDID file as usr/lib/firmware/edid/gpdwinmax.bin and not lib/firmware/edid/gpdwinmax.bin as expected.



Checked, see images.

There is this other folder but I didn't create it? Is this done automatically? :?:
Attachments
Screenshot_2020-09-20_03-33-26.png
There is a usr/lib/firmware/edid/gpdwinmax.bin
I did not create it. is it automatically done?
Screenshot_2020-09-20_03-33-26.png (28.14 KiB) Viewed 205 times
Screenshot_2020-09-20_03-25-59.png
/etc/dracut.conf.d/99-edid.conf
Screenshot_2020-09-20_03-25-59.png (18.28 KiB) Viewed 205 times
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 05:48

Have changed /etc/default/grub as suggested. No effect.
Attachments
Screenshot_2020-09-20_03-46-37.png
Screenshot_2020-09-20_03-46-37.png (52.16 KiB) Viewed 205 times
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 20th, '20, 12:06

Why did you add this also to GRUB_VIDEO ? That is not configured by default, please comment that whole line out with a #
You're also totally mixing things up. In GRUB_VIDEO you put video= with specifying an output, but you didn't put this in GRUB_CMDLINE_LINUX_DEFAULT at all, why is that?
Also the output should be eDP-1 not eDP1, seems you also didn't read the note I posted about that.

Your GRUB_CMDLINE_LINUX_DEFAULT also seems wrong. Why do you have single quotes ' around the double quotes " around the options ? This is what it should look like:

GRUB_CMDLINE_LINUX_DEFAULT="splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0 drm.edid_firmware=edid/gpdwinmax.bin"
OR with video=
GRUB_CMDLINE_LINUX_DEFAULT="splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0 video=eDP-1:800x1200 drm.edid_firmware=eDP-1:edid/gpdwinmax.bin"

Also please don't pos screenshots of text files, just post the actual content with cat. As otherwise it's very hard to tell if you maybe got linebreaks wrong or something like that.
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 13:29

doktor5000 wrote:
drm.edid_firmware=edid/gpdwinmax.bin

or additionally with video= like so:

video=eDP1:800x1200@60 drm.edid_firmware=edid/gpdwinmax.bin


Your GRUB_CMDLINE_LINUX_DEFAULT also seems wrong. Why do you have single quotes ' around the double quotes " around the options ? This is what it should look like:


I will fix those. I am copying and pasting. I didn't type or not type quotes. I just past what you put in between the lines now. So actually don't have any idea how to answer you question about that. That is to say why it's like that. Remember you asked me to let it reconfigure this with auto detect last time. I didn't do anything other than past between the quotes. I just pasted you line, and didn't add the eDP-1. Forgot.

Why did you add this also to GRUB_VIDEO ? That is not configured by default, please comment that whole line out with a #


uh, didn't understand and didn't know any better. It said video so I put it there.

You're also totally mixing things up. In GRUB_VIDEO you put video= with specifying an output, but you didn't put this in GRUB_CMDLINE_LINUX_DEFAULT at all, why is that?
Didn't realize it was meant for there.

GRUB_CMDLINE_LINUX_DEFAULT="splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0 drm.edid_firmware=edid/gpdwinmax.bin"
OR with video=
GRUB_CMDLINE_LINUX_DEFAULT="splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0 video=eDP-1:800x1200 drm.edid_firmware=eDP-1:edid/gpdwinmax.bin"


I will fix these errors as soon as possible and post the results. When I am back on the unit.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

Re: Mageia on GPD Win Max, can it?

Postby doktor5000 » Sep 20th, '20, 15:35

Sabungayam wrote:
Your GRUB_CMDLINE_LINUX_DEFAULT also seems wrong. Why do you have single quotes ' around the double quotes " around the options ? This is what it should look like:


I will fix those. I am copying and pasting. I didn't type or not type quotes. I just past what you put in between the lines now. So actually don't have any idea how to answer you question about that. That is to say why it's like that. Remember you asked me to let it reconfigure this with auto detect last time. I didn't do anything other than past between the quotes.

I've never pasted the complete line, and I've also never used single quotes. And at first the line looked like this, from your post:

Code: Select all
GRUB_CMDLINE_LINUX_DEFAULT=" splash quiet noiswmd resume=UUID=dfa7e552-30b5-4b65-97fc-214ae11b35d2 audit=0" drm_kms_helper.edid_firmware=:edid/gpdwinmax.bin


You should pay attention to such details, it's pretty hard to spot that if you don't put the options as they are mentioned - that's definitely not copy&paste, if you even switch the ordering of the options later on.
Cauldron is not for the faint of heart!
Caution: Hot, bubbling magic inside. May explode or cook your kittens!
----
Disclaimer: Beware of allergic reactions in answer to unconstructive complaint-type posts
User avatar
doktor5000
 
Posts: 16072
Joined: Jun 4th, '11, 10:10
Location: Leipzig, Germany

Re: Mageia on GPD Win Max, can it?

Postby Sabungayam » Sep 20th, '20, 17:41

I apologize if you think I am saying it came from you. That is not what I mean at all nor intend to imply.

Just really I have no answer as to why it's like that. Usually what you put here I just copy & paste that's all I mean but that doesn't mean I didn't fumble around & do something silly which I am sure I did.
Sabungayam
 
Posts: 119
Joined: Aug 18th, '20, 06:52

PreviousNext

Return to Basic support

Who is online

Users browsing this forum: Google [Bot] and 1 guest