Error 2 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 28 eb 84 e4 Error: UNC 8 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 28 eb 84 e4 08 00:22:42.031 READ DMA
c8 00 08 d0 1b 86 e4 08 00:22:42.031 READ DMA
ea 00 00 97 b4 6b e0 08 00:22:42.031 FLUSH CACHE EXT
c8 00 08 90 b4 6b ea 08 00:22:42.031 READ DMA
ca 00 08 08 c5 6c ea 08 00:22:42.031 WRITE DMA
Error 1 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d8 28 eb 84 e4 Error: UNC 216 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 10 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 08 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 00 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 b0 1c 46 e4 08 00:22:42.030 READ DMA
c8 00 f8 10 f2 44 e4 08 00:22:42.030 READ DMA
[root@newport greg]# smartctl --all /dev/sda
smartctl 6.5 2016-05-07 r4318 [i686-linux-4.14.44-server-2.mga6] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J9CZ913936
LU WWN Device Id: 5 0024e9 203663eb1
Firmware Version: 1AJ10001
User Capacity: 1,000,203,804,160 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jun 9 09:06:05 2018 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9420) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 157) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 93
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 070 069 025 Pre-fail Always - 9318
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 500
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 42194
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 541
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 8
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 051 000 Old_age Always - 29 (Min/Max 9/49)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 75
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 542
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 28 eb 84 e4 Error: UNC 8 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 28 eb 84 e4 08 00:22:42.031 READ DMA
c8 00 08 d0 1b 86 e4 08 00:22:42.031 READ DMA
ea 00 00 97 b4 6b e0 08 00:22:42.031 FLUSH CACHE EXT
c8 00 08 90 b4 6b ea 08 00:22:42.031 READ DMA
ca 00 08 08 c5 6c ea 08 00:22:42.031 WRITE DMA
Error 1 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d8 28 eb 84 e4 Error: UNC 216 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 10 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 08 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 00 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 b0 1c 46 e4 08 00:22:42.030 READ DMA
c8 00 f8 10 f2 44 e4 08 00:22:42.030 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
First
smartctl -t long /dev/sda
then a few hours later..
smartctl -all /dev/sda
smartctl 6.5 2016-05-07 r4318 [i686-linux-4.14.44-server-2.mga6] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J9CZ913936
LU WWN Device Id: 5 0024e9 203663eb1
Firmware Version: 1AJ10001
User Capacity: 1,000,203,804,160 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jun 9 12:17:28 2018 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9420) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 157) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 93
2 Throughput_Performance 0x0026 055 055 000 Old_age Always - 8681
3 Spin_Up_Time 0x0023 070 069 025 Pre-fail Always - 9318
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 500
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 42197
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 541
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 8
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 051 000 Old_age Always - 32 (Min/Max 9/49)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 75
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 542
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 28 eb 84 e4 Error: UNC 8 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 28 eb 84 e4 08 00:22:42.031 READ DMA
c8 00 08 d0 1b 86 e4 08 00:22:42.031 READ DMA
ea 00 00 97 b4 6b e0 08 00:22:42.031 FLUSH CACHE EXT
c8 00 08 90 b4 6b ea 08 00:22:42.031 READ DMA
ca 00 08 08 c5 6c ea 08 00:22:42.031 WRITE DMA
Error 1 occurred at disk power-on lifetime: 37482 hours (1561 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d8 28 eb 84 e4 Error: UNC 216 sectors at LBA = 0x0484eb28 = 75819816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 f0 10 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 08 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 00 eb 84 e4 08 00:22:42.030 READ DMA
c8 00 08 b0 1c 46 e4 08 00:22:42.030 READ DMA
c8 00 f8 10 f2 44 e4 08 00:22:42.030 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 42197 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
gregM wrote:Reboot still has the same results 2 read-only partitions and 2 unmounted partitions. Remount to read-write mode and mount the unmounted ones and I can login and scratch my head and wonder...
If anyone can give any insight in the SMART errors and Attributes from the previous post, it would be appreciated.
journalctl -ab > /path/to/journal.log
doktor5000 wrote:Boot regularly, open a terminal and runwhere /path/to/journal.log would be writing to some other place outside that disk.
- Code: Select all
journalctl -ab > /path/to/journal.log
FSTAB snip
# Entry for /dev/sda1 :
UUID=21e67610-e9ad-463e-a518-1a0da236e386 / ext4 relatime,acl 1 1
# Entry for /dev/sda6 :
UUID=4a8129e3-c8e8-45f3-beec-2b8d2f36773b /usr ext4 relatime,acl 1 2
JOURNALCTL snip
Jun 09 17:32:20 newport.nwt.net.au kernel: EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: data=ordered
Jun 09 17:32:20 newport.nwt.net.au dracut: Checking ext4: /dev/disk/by-uuid/21e67610-e9ad-463e-a518-1a0da236e386
Jun 09 17:32:20 newport.nwt.net.au dracut: issuing e2fsck -a /dev/disk/by-uuid/21e67610-e9ad-463e-a518-1a0da236e386
Jun 09 17:32:20 newport.nwt.net.au dracut: /dev/disk/by-uuid/21e67610-e9ad-463e-a518-1a0da236e386: clean, 6308/512064 files, 450756/2046208 blocks
Jun 09 17:32:20 newport.nwt.net.au dracut: Mounting /dev/disk/by-uuid/21e67610-e9ad-463e-a518-1a0da236e386 with -o rw,relatime,data=ordered,ro
Jun 09 17:32:20 newport.nwt.net.au kernel: EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: data=ordered
Jun 09 17:32:20 newport.nwt.net.au dracut: Mounted root filesystem /dev/sda1
Jun 09 17:32:20 newport.nwt.net.au dracut: Checking ext4: /dev/disk/by-uuid/4a8129e3-c8e8-45f3-beec-2b8d2f36773b
Jun 09 17:32:20 newport.nwt.net.au dracut: issuing e2fsck -a /dev/disk/by-uuid/4a8129e3-c8e8-45f3-beec-2b8d2f36773b
Jun 09 17:32:20 newport.nwt.net.au dracut: /dev/disk/by-uuid/4a8129e3-c8e8-45f3-beec-2b8d2f36773b: clean, 1454392/4481024 files, 9133896/17918066 blocks
Jun 09 17:32:20 newport.nwt.net.au dracut: Mounting /usr with -o relatime,acl,ro
Jun 09 17:32:20 newport.nwt.net.au kernel: EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: acl
jun 08 08:18:54 svarten dracut: issuing e2fsck -a /dev/vg-mga/root
jun 08 08:18:54 svarten dracut: /dev/vg-mga/root: clean, 634285/2235840 files, 6057326/8977408 blocks
jun 08 08:18:54 svarten dracut: Mounting /dev/vg-mga/root with -o rw,noatime,data=ordered
jun 08 08:18:54 svarten dracut: Mounted root filesystem /dev/mapper/vg--mga-root
jun 08 08:18:54 svarten dracut: Switching root
Jun 11 09:09:33 newport.nwt.net.au kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.14.44-server-2.mga6 root=UUID=21e67610-e9ad-463e-a518-1a0da236e386 ro splash quiet noiswmd resume=UUID=9082ca25-cf93-4436-9d78-58c7f25d0a21 audit=0 vga=791
# Entry for /dev/sda1 :
UUID=21e67610-e9ad-463e-a518-1a0da236e386 / ext4 relatime,acl 1 1
# Entry for /dev/sda10 :
UUID=2c834b22-386b-4a59-87c5-1f880f712867 /data ext4 defaults,acl,relatime 1 2
# Entry for /dev/sda8 :
UUID=20f36172-74ff-483c-8735-47bcfa7b200d /home ext4 defaults,relatime,acl 1 2
## //homeport/Data /home/greg/Data cifs user,credentials=/etc/samba/auth.homeport.greg 0 0
## none /proc proc defaults 0 0
# Entry for /dev/sda9 :
UUID=6562c9ba-2783-4dad-bbb8-8f1ffd96086d /tmp ext4 acl,relatime 1 2
# Entry for /dev/sda6 :
UUID=4a8129e3-c8e8-45f3-beec-2b8d2f36773b /usr ext4 relatime,acl 1 2
# Entry for /dev/sda7 :
UUID=286d0708-9754-4b78-981d-94b018709108 /var ext4 acl,relatime 1 2
# Entry for /dev/sda5 :
UUID=9082ca25-cf93-4436-9d78-58c7f25d0a21 swap swap defaults 0 0
gregM wrote:Now I just have the issue of not all partitions being mounted at boot, /home and /data dont auto mount for some reason, but will mount happily with 'mount -a'
I added the 'defaults' option to the fstab for those 2 slices not mounted, but no change.
Here is the edited fstab, that file has been unchanges for many months, so I doubt it is the cause of that particular issue.
gregM wrote:So somewhere else is the underlying cause ... Possibly a systemd error that did not allow fstab to be read correctly during the boot sequence.
Dont think I can mark the issue [solved] .. At best it has been put to rest, and the cause remains unknown.
Users browsing this forum: No registered users and 1 guest