Mageia forum

Looking equivalent firmware dvb-usb-dib0700-1.20.fw and dvb-fe-XC4000-1.4.fw, working with kernel 3.12.13-desktop-2.mga4.

Could you please at least describe your issue so that others can understand it?
You are looking for an equivalent to what or for what exactly? What do you mean by modified version?

dib0700 firmware is contained in kernel-firmware-nonfree package:

Code: Select all

[doktor5000@Mageia4 ~]$ urpmf dvb-usb-dib0700-1.20.fw
kernel-firmware-nonfree:/lib/firmware/dvb-usb-dib0700-1.20.fw
kernel-firmware-nonfree:/lib/firmware/dvb-usb-dib0700-1.20.fw

And there's also an dvb-fe-xc5000 firmware in there:

Code: Select all

[doktor5000@Mageia4 ~]$ urpmf 'dvb-fe.*fw'
kernel-firmware-nonfree:/lib/firmware/dvb-fe-xc5000-1.6.114.fw
kernel-firmware-nonfree:/lib/firmware/dvb-fe-xc5000-1.6.114.fw

Maybe what you need is here: http://www.kernellabs.com/firmware/xc4000/ and here: http://www.linuxtv.org/wiki/index.php/P ... Stick_340e

TV tuner does not work with Mageia-4 64bit. Worked on Mageia-3 32bit
current listing:

Code: Select all

[15908.444204] dvb-usb: Pinnacle PCTV 340e HD Pro USB Stick successfully deinitialized and disconnected.
[15923.330307] 8139too 0000:05:02.0 enp5s2: link up, 100Mbps, full-duplex, lpa 0xFFFF
[16040.695947] usb 1-1.3: new high-speed USB device number 5 using ehci-pci
[16040.781690] usb 1-1.3: New USB device found, idVendor=2304, idProduct=023d
[16040.781695] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[16040.781698] usb 1-1.3: Product: PCTV 340e
[16040.781700] usb 1-1.3: Manufacturer: YUANRD
[16040.781703] usb 1-1.3: SerialNumber: 0001276AB9
[16040.782296] dvb-usb: found a 'Pinnacle PCTV 340e HD Pro USB Stick' in cold state, will try to load a firmware
[16040.782349] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[16040.984256] dib0700: firmware started successfully.
[16041.484928] dvb-usb: found a 'Pinnacle PCTV 340e HD Pro USB Stick' in warm state.
[16041.484980] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[16041.485155] DVB: registering new adapter (Pinnacle PCTV 340e HD Pro USB Stick)
[16042.292282] usb 1-1.3: DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[16042.292407] xc4000 8-0061: creating new instance
[16042.297739] xc4000: Successfully identified at address 0x61
[16042.297743] xc4000: Firmware has not been loaded previously
[16042.297819] Registered IR keymap rc-dib0700-rc5
[16042.297934] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/rc/rc1/input19
[16042.298076] rc1: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/rc/rc1
[16042.298261] dvb-usb: schedule remote query interval to 50 msecs.
[16042.298266] dvb-usb: Pinnacle PCTV 340e HD Pro USB Stick successfully initialized and connected.

My DVB-T player Kaffeine, not search for channels.

Kaffeine is dead so it can be problem,i use with artec dvb w_scan and vlc.
This scan your countrie all channels paste it to terminal as normal user not root.

Code: Select all

w_scan -X -c PL

Start kaffeine

Code: Select all

xxx@localhost ~]$ kaffeine
Object::connect: No such signal org::freedesktop::UPower::DeviceAdded(QDBusObjectPath)
Object::connect: No such signal org::freedesktop::UPower::DeviceRemoved(QDBusObjectPath)
input_bluray: (bluray_class_get_instance:1454) bluray_class_get_instance
kaffeine(30979) DvbDevice::frontendEvent: tuning failed
net_buf_ctrl: dvbspeed mode
net_buf_ctrl: dvbspeed OFF

Start vlc

Code: Select all

xxx@localhost ~]$ vlc
VLC media player 2.1.2 Rincewind (revision 2.1.2-0-ga4c4876)
[0x1db70b8] qt4 interface error: Unable to load extensions module
[0x7f68c4001ff8] main stream error: cannot pre fill buffer

The system creates

Code: Select all

/dev/dvb/adapter0
demux0
dvr0
frontend0
net0

Please next time use code tags as explained in ftp://ftp5.gwdg.de/pub/linux/mandriva/m ... e_tags.ogv

I present the result of the command w_scan -X -c PL

Code: Select all

xx@localhost ~]$ w_scan -X -c PL
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB aerial
DVB-T Europe
scan type TERRESTRIAL, channellist 4
output format czap/tzap/szap/xine
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        /dev/dvb/adapter0/frontend0 -> TERRESTRIAL "DiBcom 7000PC": good :-)
Using TERRESTRIAL frontend (adapter /dev/dvb/adapter0/frontend0)
-_-_-_-_ Getting frontend capabilities-_-_-_-_
Using DVB API 5.a
frontend 'DiBcom 7000PC' supports
INVERSION_AUTO
QAM_AUTO
TRANSMISSION_MODE_AUTO
GUARD_INTERVAL_AUTO
HIERARCHY_AUTO
FEC_AUTO
FREQ (44.25MHz ... 867.25MHz)
-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_
Scanning 7MHz frequencies...
177500: (time: 00:00)
to
Scanning 8MHz frequencies...
474000: (time: 02:37)
to
858000: (time: 18:13)

ERROR: Sorry - i couldn't get any working frequency/transponder
 Nothing to scan!!

What is the cause of the problem?

That command seems to be wrong,try these commands one by one.Is that analog or digitv adapter ?.

Code: Select all

w_scan -fc -c PL -x

w_scan -v -fc -c PL -t 3 -x

w_scan -vv -fc -c PL -i 0 -t 3 -x

w_scan -vvv -fc -c PL -i 1 -t 3 -x

w_scan -vvv -fc -c PL -Q 1 -S 0 -i 1 -t 3 -x

If those works you can add >> channels.conf end of that command so it will save it to file.

Code: Select all

@localhost ~]$ w_scan -fc -c PL -x
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB cable
DVB-C
scan type CABLE, channellist 7
output format initial tuning data
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        /dev/dvb/adapter0/frontend0 -> "DiBcom 7000PC" doesnt support CABLE -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

@localhost ~]$ w_scan -v -fc -c PL -t 3 -x
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB cable
DVB-C
scan type CABLE, channellist 7
output format initial tuning data
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        /dev/dvb/adapter0/frontend0 -> "DiBcom 7000PC" doesnt support CABLE -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.
 
@localhost ~]$ w_scan -vv -fc -c PL -i 0 -t 3 -x
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB cable
DVB-C
scan type CABLE, channellist 7
output format initial tuning data
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        ===================== DiBcom 7000PC ====================================
        len = 1
        0x00: 03                                              : 
        ========================================================================                                           
        /dev/dvb/adapter0/frontend0 -> "DiBcom 7000PC" doesnt support CABLE -> SEARCH NEXT ONE.                           
main:3220: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****                                                                 
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

@localhost ~]$ w_scan -vvv -fc -c PL -i 1 -t 3 -x
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB cable
DVB-C
scan type CABLE, channellist 7
output format initial tuning data
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        ===================== DiBcom 7000PC ====================================
        len = 1
        0x00: 03                                              : 
        ========================================================================
        /dev/dvb/adapter0/frontend0 -> "DiBcom 7000PC" doesnt support CABLE -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

@localhost ~]$ w_scan -vvv -fc -c PL -Q 1 -S 0 -i 1 -t 3 -x
w_scan version 20120605 (compiled for DVB API 5.9)
using settings for POLAND
DVB cable
DVB-C
scan type CABLE, channellist 7
output format initial tuning data
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
        ===================== DiBcom 7000PC ====================================
        len = 1
        0x00: 03                                              : 
        ========================================================================
        /dev/dvb/adapter0/frontend0 -> "DiBcom 7000PC" doesnt support CABLE -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE CABLE CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

In Poland we have DVB-T standard H.264 codec, 8-channel MUX. My TV frequency: 634MHz, 698MHz, 746MHz.
w_scan, runs a scan frequency, finds nothing

@ozky: The last scan commands you asked to run only seem to scan for DVB-C ...

TV-tuner on Mageia-3 with old kernel 3.10.28 and the same firmware works great.
Thank you for trying to help.
MiReJ

Yes it can be changed to scan dvb-t with w_scan -X -t PL

ozky
My PCTV 340e-simulates the work, it really not work.
I have limited time I return to the theme for 3-weeks.
Regards

Dear colleagues, my PCTV 340e-overheated and did not even work on Windows.
Problem solved

Please mark the thread accordingly by editing the topic of the first post and prefix it by [DONE], thanks