Mageia Forum

Share the magic
http://forums.mageia.org/de/

[Bugmeldung] CD-Laufwerk öffnet sich ungewollt

http://forums.mageia.org/de/viewtopic.php?f=7&t=3832

Seite 1 von 2

[Bugmeldung] CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 13:03
von ikseran
Seit dem neuesten Update, öffnet sich unter MATE (Mga8) das CD-Laufwerk automatisch, wenn ich den Rechner aus dem Bereitschaftsmodus starte.

Wie ist da Abhilfe möglich?

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 15:38
von man-draker
ikseran hat geschrieben:Wie ist da Abhilfe möglich?

Bestimmt.
Zum Beispiel
- Bereitschaftsmodus nicht mehr benutzen
- Stromkabel abziehen

oder

- Logfiles überprüfen, warum das Ding überhaupt angesprochen wird.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 16:02
von ikseran
Die ersten beiden Möglichkeiten stecke ich eher in die humoristische Ecke.

Wie überprüfe ich die Logfiles? Und welche?

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 16:04
von doktor5000
Logfiles werden eigtl. immer via journalctl geprüft, und die Frage nach welchem beantwortet sich damit auch.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 16:29
von ikseran
wie kann man die Ausgabe eingrenzen bzw. wonach suche ich?

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 13th, '21, 16:41
von doktor5000
Die Ausgabe kann man mittels -b oder --since oder --until eingrenzen oder einfach mit der Suche im pager (mittels / ).
man journalctl ist dein Freund für weitere Filter-Optionen.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 07:39
von ikseran
Code: Alles auswählen
Jul 14 08:28:20 Art-ig kernel: PM: suspend entry (deep)
Jul 14 08:28:22 Art-ig kernel: Filesystems sync: 1.198 seconds
Jul 14 08:28:31 Art-ig kernel: Freezing user space processes ... (elapsed 0.001 seconds) done.
Jul 14 08:28:31 Art-ig kernel: OOM killer disabled.
Jul 14 08:28:31 Art-ig kernel: Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Jul 14 08:28:31 Art-ig kernel: printk: Suspending console(s) (use no_console_suspend to debug)
Jul 14 08:28:31 Art-ig kernel: wlp4s0: deauthenticating from 64:70:02:f7:01:6e by local choice (Reason: 3=DEAUTH_LEAVING)
Jul 14 08:28:31 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 08:28:31 Art-ig kernel: sd 3:0:0:0: [sdb] Synchronizing SCSI cache
Jul 14 08:28:31 Art-ig kernel: sd 2:0:0:0: [sda] Synchronizing SCSI cache
Jul 14 08:28:31 Art-ig kernel: sd 3:0:0:0: [sdb] Stopping disk
Jul 14 08:28:31 Art-ig kernel: sd 2:0:0:0: [sda] Stopping disk
Jul 14 08:28:31 Art-ig kernel: ACPI: Preparing to enter system sleep state S3
Jul 14 08:28:31 Art-ig kernel: PM: Saving platform NVS memory
Jul 14 08:28:31 Art-ig kernel: Disabling non-boot CPUs ...
Jul 14 08:28:31 Art-ig kernel: IRQ 23: no longer affine to CPU1
Jul 14 08:28:31 Art-ig kernel: IRQ 30: no longer affine to CPU1
Jul 14 08:28:31 Art-ig kernel: smpboot: CPU 1 is now offline
Jul 14 08:28:31 Art-ig kernel: IRQ 16: no longer affine to CPU2
Jul 14 08:28:31 Art-ig kernel: IRQ 19: no longer affine to CPU2
Jul 14 08:28:31 Art-ig kernel: IRQ 29: no longer affine to CPU2
Jul 14 08:28:31 Art-ig kernel: smpboot: CPU 2 is now offline
Jul 14 08:28:31 Art-ig kernel: IRQ 31: no longer affine to CPU3
Jul 14 08:28:31 Art-ig kernel: IRQ 35: no longer affine to CPU3
Jul 14 08:28:31 Art-ig kernel: smpboot: CPU 3 is now offline
Jul 14 08:28:31 Art-ig kernel: ACPI: Low-level resume complete
Jul 14 08:28:31 Art-ig kernel: PM: Restoring platform NVS memory
Jul 14 08:28:31 Art-ig kernel: smpboot: Scheduler frequency invariance went wobbly, disabling!
Jul 14 08:28:31 Art-ig kernel: Enabling non-boot CPUs ...
Jul 14 08:28:31 Art-ig kernel: x86: Booting SMP configuration:
Jul 14 08:28:31 Art-ig kernel: smpboot: Booting Node 0 Processor 1 APIC 0x2
Jul 14 08:28:31 Art-ig kernel: CPU1 is up
Jul 14 08:28:31 Art-ig kernel: smpboot: Booting Node 0 Processor 2 APIC 0x4
Jul 14 08:28:31 Art-ig kernel: CPU2 is up
Jul 14 08:28:31 Art-ig kernel: smpboot: Booting Node 0 Processor 3 APIC 0x6
Jul 14 08:28:31 Art-ig kernel: CPU3 is up
Jul 14 08:28:31 Art-ig kernel: ACPI: Waking up from system sleep state S3
Jul 14 08:28:31 Art-ig kernel: sd 2:0:0:0: [sda] Starting disk
Jul 14 08:28:31 Art-ig kernel: sd 3:0:0:0: [sdb] Starting disk
Jul 14 08:28:31 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 08:28:31 Art-ig kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
Jul 14 08:28:31 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
Jul 14 08:28:31 Art-ig kernel: ata6.00: configured for UDMA/100
Jul 14 08:28:31 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full - flow control rx/tx
Jul 14 08:28:31 Art-ig kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
Jul 14 08:28:31 Art-ig kernel: ata3.00: configured for UDMA/133
Jul 14 08:28:31 Art-ig kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul 14 08:28:31 Art-ig kernel: ata4.00: configured for UDMA/133
Jul 14 08:28:31 Art-ig kernel: OOM killer enabled.
Jul 14 08:28:31 Art-ig kernel: Restarting tasks ...
Jul 14 08:28:31 Art-ig kernel: pci_bus 0000:04: Allocating resources
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: bridge window [io  0x1000-0x0fff] to [bus 04] add_size 1000
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size 0x1000]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  size 0x1000]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size 0x1000]
Jul 14 08:28:31 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  size 0x1000]
Jul 14 08:28:31 Art-ig kernel: done.
Jul 14 08:28:31 Art-ig kernel: video LNXVIDEO:00: Restoring backlight state
Jul 14 08:28:31 Art-ig kernel: PM: suspend exit
Jul 14 08:28:32 Art-ig kernel: wlp4s0: authenticate with 64:70:02:f7:01:6e
Jul 14 08:28:32 Art-ig kernel: wlp4s0: send auth to 64:70:02:f7:01:6e (try 1/3)
Jul 14 08:28:32 Art-ig kernel: wlp4s0: authenticated
Jul 14 08:28:32 Art-ig kernel: wlp4s0: associate with 64:70:02:f7:01:6e (try 1/3)
Jul 14 08:28:32 Art-ig kernel: wlp4s0: RX AssocResp from 64:70:02:f7:01:6e (capab=0x431 status=0 aid=2)
Jul 14 08:28:32 Art-ig kernel: wlp4s0: associated


Dieser Abschnitt der Ausgabe bezieht sich auf den kurzen Zeitausschnitt nachdem ich den Bereitschaftsmodus wieder beendet habe. Ich selbst kann nichts daraus ersehen, worin der Grund für das ungewollte Öffnen des DVD-Laufwerks liegen könnte, da ich viel zu wenig Ahnung habe.

Wie ich gerade gesehen habe, ergibt sich das gleiche Verhalten, wenn ich in Plasma aus dem Standbymodus in den Betrieb wechsle.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 08:51
von man-draker
Da in dem von dir geposteten Abschnitt zwar die Controller ata6 und ata3 initialisiert werden, nicht aber die Laufwerke gesucht, konfiguriert und eingebunden, ist er auch nicht aussagekräftig. (Außer, dass wohl die HD/SSD am ata3 hängt und das CD/DVD-Lw am ata6).

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 10:42
von ikseran
Und wie komme ich zu einem aussagekräftigen Ergebnis?

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 12:48
von man-draker
Indem du das Log aus den z.B. 30 Sekunden nach "Jul 14 08:28:32" postest.
Bzw. nicht nur die ersten Sekunden nach dem Start, sondern, was innerhalb der ersten 30 bis 60 Sekunden passiert.
Wenn es für das Einfügen zu lang ist, kannst du es als Datei anhängen.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 16:08
von ikseran
Code: Alles auswählen
Jul 14 15:08:49 Art-ig kernel: io scheduler kyber registered
Jul 14 15:08:49 Art-ig kernel: io scheduler bfq registered
Jul 14 15:08:49 Art-ig kernel: vesafb: mode is 1024x768x16, linelength=2048, pa>
Jul 14 15:08:49 Art-ig kernel: vesafb: scrolling: redraw
Jul 14 15:08:49 Art-ig kernel: vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Jul 14 15:08:49 Art-ig kernel: vesafb: framebuffer at 0xe0000000, mapped to 0x0>
Jul 14 15:08:49 Art-ig kernel: Console: switching to colour frame buffer device>
Jul 14 15:08:49 Art-ig kernel: fb0: VESA VGA frame buffer device
Jul 14 15:08:49 Art-ig kernel: intel_idle: MWAIT substates: 0x42120
Jul 14 15:08:49 Art-ig kernel: intel_idle: v0.5.1 model 0x3C
Jul 14 15:08:49 Art-ig kernel: intel_idle: Local APIC timer is reliable in all >
Jul 14 15:08:49 Art-ig kernel: Serial: 8250/16550 driver, 4 ports, IRQ sharing >
Jul 14 15:08:49 Art-ig kernel: Linux agpgart interface v0.103
Jul 14 15:08:49 Art-ig kernel: brd: module loaded
Jul 14 15:08:49 Art-ig kernel: ahci 0000:00:1f.2: version 3.0
Jul 14 15:08:49 Art-ig kernel: ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 por>
Jul 14 15:08:49 Art-ig kernel: ahci 0000:00:1f.2: flags: 64bit ncq led clo pio >
Jul 14 15:08:49 Art-ig kernel: scsi host0: ahci
Jul 14 15:08:49 Art-ig kernel: scsi host1: ahci
Jul 14 15:08:49 Art-ig kernel: scsi host2: ahci
Jul 14 15:08:49 Art-ig kernel: scsi host3: ahci
Jul 14 15:08:49 Art-ig kernel: scsi host4: ahci
Jul 14 15:08:49 Art-ig kernel: scsi host5: ahci
Jul 14 15:08:49 Art-ig kernel: ata1: DUMMY
Jul 14 15:08:49 Art-ig kernel: ata2: DUMMY
Jul 14 15:08:49 Art-ig kernel: ata3: SATA max UDMA/133 abar m2048@0xf7e19000 po>
Jul 14 15:08:49 Art-ig kernel: ata4: SATA max UDMA/133 abar m2048@0xf7e19000 po>
Jul 14 15:08:49 Art-ig kernel: ata5: DUMMY
Jul 14 15:08:49 Art-ig kernel: ata6: SATA max UDMA/133 abar m2048@0xf7e19000 po>
Jul 14 15:08:49 Art-ig kernel: i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x>
Jul 14 15:08:49 Art-ig kernel: i8042: PNP: PS/2 appears to have AUX port disabl>
Jul 14 15:08:49 Art-ig kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Jul 14 15:08:49 Art-ig kernel: mousedev: PS/2 mouse device common for all mice
Jul 14 15:08:49 Art-ig kernel: rtc_cmos 00:02: RTC can wake from S4
Jul 14 15:08:49 Art-ig kernel: rtc_cmos 00:02: registered as rtc0
Jul 14 15:08:49 Art-ig kernel: rtc_cmos 00:02: setting system clock to 2021-07->
Jul 14 15:08:49 Art-ig kernel: rtc_cmos 00:02: alarms up to one month, y3k, 242>
Jul 14 15:08:49 Art-ig kernel: intel_pstate: Intel P-state driver initializing
Jul 14 15:08:49 Art-ig kernel: ledtrig-cpu: registered to indicate activity on >
Jul 14 15:08:49 Art-ig kernel: Key type dns_resolver registered
Jul 14 15:08:49 Art-ig kernel: mpls_gso: MPLS GSO support
Jul 14 15:08:49 Art-ig kernel: microcode: sig=0x306c3, pf=0x2, revision=0x28
Jul 14 15:08:49 Art-ig kernel: microcode: Microcode Update Driver: v2.2.
Jul 14 15:08:49 Art-ig kernel: IPI shorthand broadcast: enabled
Jul 14 15:08:49 Art-ig kernel: sched_clock: Marking stable (597364766, 226921)->
Jul 14 15:08:49 Art-ig kernel: registered taskstats version 1
Jul 14 15:08:49 Art-ig kernel: Loading compiled-in X.509 certificates
Jul 14 15:08:49 Art-ig kernel: zswap: loaded using pool lzo/zbud
Jul 14 15:08:49 Art-ig kernel: Key type ._fscrypt registered
Jul 14 15:08:49 Art-ig kernel: Key type .fscrypt registered
Jul 14 15:08:49 Art-ig kernel: Key type fscrypt-provisioning registered
Jul 14 15:08:49 Art-ig kernel: Btrfs loaded, crc32c=crc32c-generic
Jul 14 15:08:49 Art-ig kernel: Key type encrypted registered
Jul 14 15:08:49 Art-ig kernel: PM:   Magic number: 13:500:129
Jul 14 15:08:49 Art-ig kernel: nvmem cmos_nvram0: hash matches
Jul 14 15:08:49 Art-ig kernel: event_source kprobe: hash matches
Jul 14 15:08:49 Art-ig kernel: acpi PNP0C02:01: hash matches
Jul 14 15:08:49 Art-ig kernel: acpi device:04: hash matches
Jul 14 15:08:49 Art-ig kernel: BIOS EDD facility v0.16 2004-Jun-25, 2 devices f>
Jul 14 15:08:49 Art-ig kernel: input: AT Translated Set 2 keyboard as /devices/>
Jul 14 15:08:49 Art-ig kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SContro>
Jul 14 15:08:49 Art-ig kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SContro>
Jul 14 15:08:49 Art-ig kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SContro>
Jul 14 15:08:49 Art-ig kernel: ata4.00: ATA-8: Hitachi HDS721050CLA360, JP2OA50>
Jul 14 15:08:49 Art-ig kernel: ata4.00: 976773168 sectors, multi 16: LBA48 NCQ >
Jul 14 15:08:49 Art-ig kernel: ata3.00: ATA-8: TOSHIBA DT01ACA100, MS2OA750, ma>
Jul 14 15:08:49 Art-ig kernel: ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ>
Jul 14 15:08:49 Art-ig kernel: ata4.00: configured for UDMA/133
Jul 14 15:08:49 Art-ig kernel: ata3.00: configured for UDMA/133
Jul 14 15:08:49 Art-ig kernel: scsi 2:0:0:0: Direct-Access     ATA      TOSHIBA>
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] 1953525168 512-byte logical bl>
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] 4096-byte physical blocks
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] Write Protect is off
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] Write cache: enabled, read cac>
Jul 14 15:08:49 Art-ig kernel: scsi 3:0:0:0: Direct-Access     ATA      Hitachi>
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: [sdb] 976773168 512-byte logical blo>
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: [sdb] Write Protect is off
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: [sdb] Write cache: enabled, read cac>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ATAPI: ATAPI   iHAS122   E, 2L02, max U>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 15:08:49 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 15:08:49 Art-ig kernel: ata6.00: configured for UDMA/100
Jul 14 15:08:49 Art-ig kernel: scsi 5:0:0:0: CD-ROM            ATAPI    iHAS122>
Jul 14 15:08:49 Art-ig kernel:  sdb: sdb1 sdb2 < sdb5 >
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: [sdb] Attached SCSI disk
Jul 14 15:08:49 Art-ig kernel:  sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: [sda] Attached SCSI disk
Jul 14 15:08:49 Art-ig kernel: Freeing unused kernel image (initmem) memory: 16>
Jul 14 15:08:49 Art-ig kernel: Write protecting the kernel read-only data: 2252>
Jul 14 15:08:49 Art-ig kernel: Freeing unused kernel image (text/rodata gap) me>
Jul 14 15:08:49 Art-ig kernel: Freeing unused kernel image (rodata/data gap) me>
Jul 14 15:08:49 Art-ig kernel: x86/mm: Checked W+X mappings: passed, no W+X pag>
Jul 14 15:08:49 Art-ig kernel: x86/mm: Checking user space page tables
Jul 14 15:08:49 Art-ig kernel: x86/mm: Checked W+X mappings: passed, no W+X pag>
Jul 14 15:08:49 Art-ig kernel: Run /init as init process
Jul 14 15:08:49 Art-ig kernel:   with arguments:
Jul 14 15:08:49 Art-ig kernel:     /init
Jul 14 15:08:49 Art-ig kernel:     splash
Jul 14 15:08:49 Art-ig kernel:     noiswmd
Jul 14 15:08:49 Art-ig kernel:   with environment:
Jul 14 15:08:49 Art-ig kernel:     HOME=/
Jul 14 15:08:49 Art-ig kernel:     TERM=linux
Jul 14 15:08:49 Art-ig kernel:     BOOT_IMAGE=/boot/vmlinuz-5.10.48-desktop-1.m>
Jul 14 15:08:49 Art-ig kernel:     vga=791
Jul 14 15:08:49 Art-ig dracut: Mageia-8
Jul 14 15:08:49 Art-ig kernel: checking generic (e0000000 7ff0000) vs hw (f7800>
Jul 14 15:08:49 Art-ig kernel: checking generic (e0000000 7ff0000) vs hw (e0000>
Jul 14 15:08:49 Art-ig kernel: fb0: switching to inteldrmfb from VESA VGA
Jul 14 15:08:49 Art-ig kernel: Console: switching to colour dummy device 80x25
Jul 14 15:08:49 Art-ig kernel: i915 0000:00:02.0: vgaarb: deactivate vga console
Jul 14 15:08:49 Art-ig kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: >
Jul 14 15:08:49 Art-ig kernel: [drm] Initialized i915 1.6.0 20200917 for 0000:0>
Jul 14 15:08:49 Art-ig kernel: ACPI: Video Device [GFX0] (multi-head: yes  rom:>
Jul 14 15:08:49 Art-ig kernel: input: Video Bus as /devices/LNXSYSTM:00/LNXSYBU>
Jul 14 15:08:49 Art-ig kernel: fbcon: i915drmfb (fb0) is primary device
Jul 14 15:08:49 Art-ig kernel: Console: switching to colour frame buffer device>
Jul 14 15:08:49 Art-ig kernel: i915 0000:00:02.0: [drm] fb0: i915drmfb frame bu>
Jul 14 15:08:49 Art-ig dracut: Starting plymouth daemon
Jul 14 15:08:49 Art-ig kernel: tsc: Refined TSC clocksource calibration: 3099.9>
Jul 14 15:08:49 Art-ig kernel: clocksource: tsc: mask: 0xffffffffffffffff max_c>
Jul 14 15:08:49 Art-ig kernel: clocksource: Switched to clocksource tsc
Jul 14 15:08:49 Art-ig kernel: ACPI: bus type USB registered
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new interface driver usbfs
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new interface driver hub
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new device driver usb
Jul 14 15:08:49 Art-ig kernel: cryptd: max_cpu_qlen set to 1000
Jul 14 15:08:49 Art-ig kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EH>
Jul 14 15:08:49 Art-ig kernel: ehci-pci: EHCI PCI platform driver
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: EHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: new USB bus registered, a>
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: debug port 2
Jul 14 15:08:49 Art-ig kernel: AVX2 version of gcm_enc/dec engaged.
Jul 14 15:08:49 Art-ig kernel: AES CTR mode by8 optimization enabled
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: cache line size of 64 is >
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7e1b000
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
Jul 14 15:08:49 Art-ig kernel: usb usb1: New USB device found, idVendor=1d6b, i>
Jul 14 15:08:49 Art-ig kernel: usb usb1: New USB device strings: Mfr=3, Product>
Jul 14 15:08:49 Art-ig kernel: usb usb1: Product: EHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: usb usb1: Manufacturer: Linux 5.10.48-desktop-1.>
Jul 14 15:08:49 Art-ig kernel: usb usb1: SerialNumber: 0000:00:1a.0
Jul 14 15:08:49 Art-ig kernel: hub 1-0:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 1-0:1.0: 2 ports detected
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: EHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: new USB bus registered, a>
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: debug port 2
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: cache line size of 64 is >
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7e1a000
Jul 14 15:08:49 Art-ig kernel: sr 5:0:0:0: [sr0] scsi3-mmc drive: 48x/48x write>
Jul 14 15:08:49 Art-ig kernel: cdrom: Uniform CD-ROM driver Revision: 3.20
Jul 14 15:08:49 Art-ig kernel: ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
Jul 14 15:08:49 Art-ig kernel: usb usb2: New USB device found, idVendor=1d6b, i>
Jul 14 15:08:49 Art-ig kernel: usb usb2: New USB device strings: Mfr=3, Product>
Jul 14 15:08:49 Art-ig kernel: usb usb2: Product: EHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: usb usb2: Manufacturer: Linux 5.10.48-desktop-1.>
Jul 14 15:08:49 Art-ig kernel: usb usb2: SerialNumber: 0000:00:1d.0
Jul 14 15:08:49 Art-ig kernel: hub 2-0:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 2-0:1.0: 2 ports detected
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: xHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: new USB bus registered, a>
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci>
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: cache line size of 64 is >
Jul 14 15:08:49 Art-ig kernel: usb usb3: New USB device found, idVendor=1d6b, i>
Jul 14 15:08:49 Art-ig kernel: usb usb3: New USB device strings: Mfr=3, Product>
Jul 14 15:08:49 Art-ig kernel: usb usb3: Product: xHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: usb usb3: Manufacturer: Linux 5.10.48-desktop-1.>
Jul 14 15:08:49 Art-ig kernel: usb usb3: SerialNumber: 0000:00:14.0
Jul 14 15:08:49 Art-ig kernel: hub 3-0:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 3-0:1.0: 14 ports detected
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: xHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: new USB bus registered, a>
Jul 14 15:08:49 Art-ig kernel: xhci_hcd 0000:00:14.0: Host supports USB 3.0 Sup>
Jul 14 15:08:49 Art-ig kernel: usb usb4: New USB device found, idVendor=1d6b, i>
Jul 14 15:08:49 Art-ig kernel: usb usb4: New USB device strings: Mfr=3, Product>
Jul 14 15:08:49 Art-ig kernel: usb usb4: Product: xHCI Host Controller
Jul 14 15:08:49 Art-ig kernel: usb usb4: Manufacturer: Linux 5.10.48-desktop-1.>
Jul 14 15:08:49 Art-ig kernel: usb usb4: SerialNumber: 0000:00:14.0
Jul 14 15:08:49 Art-ig kernel: hub 4-0:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 4-0:1.0: 6 ports detected
Jul 14 15:08:49 Art-ig kernel: sr 5:0:0:0: Attached scsi CD-ROM sr0
Jul 14 15:08:49 Art-ig kernel: usb 1-1: new high-speed USB device number 2 usin>
Jul 14 15:08:49 Art-ig kernel: usb 2-1: new high-speed USB device number 2 usin>
Jul 14 15:08:49 Art-ig kernel: usb 3-1: new full-speed USB device number 2 usin>
Jul 14 15:08:49 Art-ig kernel: usb 1-1: New USB device found, idVendor=8087, id>
Jul 14 15:08:49 Art-ig kernel: usb 1-1: New USB device strings: Mfr=0, Product=>
Jul 14 15:08:49 Art-ig kernel: hub 1-1:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 1-1:1.0: 6 ports detected
Jul 14 15:08:49 Art-ig kernel: usb 3-1: New USB device found, idVendor=219c, id>
Jul 14 15:08:49 Art-ig kernel: usb 3-1: New USB device strings: Mfr=1, Product=>
Jul 14 15:08:49 Art-ig kernel: usb 3-1: Product: SecureSignToken
Jul 14 15:08:49 Art-ig kernel: usb 3-1: Manufacturer: SEALONE AG
Jul 14 15:08:49 Art-ig kernel: usb 2-1: New USB device found, idVendor=8087, id>
Jul 14 15:08:49 Art-ig kernel: usb 2-1: New USB device strings: Mfr=0, Product=>
Jul 14 15:08:49 Art-ig kernel: hub 2-1:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 2-1:1.0: 8 ports detected
Jul 14 15:08:49 Art-ig kernel: usb-storage 3-1:1.0: USB Mass Storage device det>
Jul 14 15:08:49 Art-ig kernel: scsi host6: usb-storage 3-1:1.0
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new interface driver usb-sto>
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new interface driver uas
Jul 14 15:08:49 Art-ig kernel: hid: raw HID events driver (C) Jiri Kosina
Jul 14 15:08:49 Art-ig kernel: usbcore: registered new interface driver usbhid
Jul 14 15:08:49 Art-ig kernel: usbhid: USB HID core driver
Jul 14 15:08:49 Art-ig kernel: hid-generic 0003:219C:0010.0001: hiddev0,hidraw0>
Jul 14 15:08:49 Art-ig kernel: usb 3-3: new high-speed USB device number 3 usin>
Jul 14 15:08:49 Art-ig kernel: usb 3-3: New USB device found, idVendor=0409, id>
Jul 14 15:08:49 Art-ig kernel: usb 3-3: New USB device strings: Mfr=0, Product=>
Jul 14 15:08:49 Art-ig kernel: hub 3-3:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 3-3:1.0: 4 ports detected
Jul 14 15:08:49 Art-ig kernel: usb 3-10: new high-speed USB device number 4 usi>
Jul 14 15:08:49 Art-ig kernel: usb 3-10: New USB device found, idVendor=0424, i>
Jul 14 15:08:49 Art-ig kernel: usb 3-10: New USB device strings: Mfr=0, Product>
Jul 14 15:08:49 Art-ig kernel: hub 3-10:1.0: USB hub found
Jul 14 15:08:49 Art-ig kernel: hub 3-10:1.0: 4 ports detected
Jul 14 15:08:49 Art-ig kernel: usb 3-3.4: new low-speed USB device number 5 usi>
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): INFO: recovery required on reado>
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): write access will be enabled dur>
Jul 14 15:08:49 Art-ig kernel: usb 3-3.4: New USB device found, idVendor=046d, >
Jul 14 15:08:49 Art-ig kernel: usb 3-3.4: New USB device strings: Mfr=1, Produc>
Jul 14 15:08:49 Art-ig kernel: usb 3-3.4: Product: USB-PS/2 Optical Mouse
Jul 14 15:08:49 Art-ig kernel: usb 3-3.4: Manufacturer: Logitech
Jul 14 15:08:49 Art-ig kernel: input: Logitech USB-PS/2 Optical Mouse as /devic>
Jul 14 15:08:49 Art-ig kernel: hid-generic 0003:046D:C051.0002: input,hidraw1: >
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): recovery complete
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): mounted filesystem with ordered >
Jul 14 15:08:49 Art-ig dracut: Checking ext4: /dev/disk/by-uuid/a2b0b662-162d-4>
Jul 14 15:08:49 Art-ig dracut: issuing e2fsck -a  /dev/disk/by-uuid/a2b0b662-16>
Jul 14 15:08:49 Art-ig dracut: /dev/disk/by-uuid/a2b0b662-162d-43d4-9d14-ea1331>
Jul 14 15:08:49 Art-ig dracut: Mounting /dev/disk/by-uuid/a2b0b662-162d-43d4-9d>
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): mounted filesystem with ordered >
Jul 14 15:08:49 Art-ig dracut: Mounted root filesystem /dev/sda1
Jul 14 15:08:49 Art-ig dracut: Checking ext4: /dev/disk/by-uuid/c3e1c706-c6a7-4>
Jul 14 15:08:49 Art-ig dracut: issuing e2fsck -a  /dev/disk/by-uuid/c3e1c706-c6>
Jul 14 15:08:49 Art-ig kernel: scsi 6:0:0:0: CD-ROM            SEALONE  SecureS>
Jul 14 15:08:49 Art-ig kernel: sr 6:0:0:0: [sr1] scsi3-mmc drive: 99x/99x cd/rw>
Jul 14 15:08:49 Art-ig kernel: sr 6:0:0:0: Attached scsi CD-ROM sr1
Jul 14 15:08:49 Art-ig dracut: /usr2: recovering journal
Jul 14 15:08:49 Art-ig dracut: /usr2: clean, 433295/960992 files, 2853116/38407>
Jul 14 15:08:49 Art-ig dracut: Mounting /usr with -o noatime,acl,ro
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda8): mounted filesystem with ordered >
Jul 14 15:08:49 Art-ig dracut: Switching root
Jul 14 15:08:49 Art-ig systemd[1]: Inserted module 'autofs4'
Jul 14 15:08:49 Art-ig kernel: NET: Registered protocol family 10
Jul 14 15:08:49 Art-ig kernel: Segment Routing with IPv6
Jul 14 15:08:49 Art-ig systemd[1]: systemd 246 running in system mode. (+PAM +A>
Jul 14 15:08:49 Art-ig systemd[1]: Detected architecture x86-64.
Jul 14 15:08:49 Art-ig systemd[1]: Set hostname to <Art-ig>.
Jul 14 15:08:49 Art-ig systemd[1]: usr.mount: Unit is bound to inactive unit de>
Jul 14 15:08:49 Art-ig systemd[1]: Queued start job for default target Graphica>
Jul 14 15:08:49 Art-ig systemd[1]: Created slice system-getty.slice.
Jul 14 15:08:49 Art-ig systemd[1]: Created slice system-modprobe.slice.
Jul 14 15:08:49 Art-ig systemd[1]: Created slice system-systemd\x2dfsck.slice.
Jul 14 15:08:49 Art-ig systemd[1]: Created slice User and Session Slice.
Jul 14 15:08:49 Art-ig systemd[1]: Started Forward Password Requests to Wall Di>
Jul 14 15:08:49 Art-ig systemd[1]: Set up automount Arbitrary Executable File F>
Jul 14 15:08:49 Art-ig systemd[1]: Reached target Login Prompts.
Jul 14 15:08:49 Art-ig systemd[1]: Reached target Remote File Systems.
Jul 14 15:08:49 Art-ig systemd[1]: Reached target RPC Port Mapper.
Jul 14 15:08:49 Art-ig systemd[1]: Reached target Slices.
Jul 14 15:08:49 Art-ig systemd[1]: Listening on Device-mapper event daemon FIFO>
Jul 14 15:08:49 Art-ig systemd[1]: Listening on Process Core Dump Socket.
Jul 14 15:08:49 Art-ig systemd[1]: Listening on initctl Compatibility Named Pip>
Jul 14 15:08:49 Art-ig systemd[1]: Condition check resulted in Journal Audit So>
Jul 14 15:08:49 Art-ig systemd[1]: Listening on Journal Socket (/dev/log).
Jul 14 15:08:49 Art-ig systemd[1]: Listening on Journal Socket.
Jul 14 15:08:49 Art-ig systemd[1]: Listening on udev Control Socket.
Jul 14 15:08:49 Art-ig systemd[1]: Listening on udev Kernel Socket.
Jul 14 15:08:49 Art-ig systemd[1]: Mounting Huge Pages File System...
Jul 14 15:08:49 Art-ig systemd[1]: Mounting POSIX Message Queue File System...
Jul 14 15:08:49 Art-ig systemd[1]: Mounting Kernel Debug File System...
Jul 14 15:08:49 Art-ig systemd[1]: Mounting Kernel Trace File System...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Load legacy module configuration...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Create list of static device nodes >
Jul 14 15:08:49 Art-ig systemd[1]: Starting Monitoring of LVM2 mirrors, snapsho>
Jul 14 15:08:49 Art-ig systemd[1]: Starting Software RAID Monitor Takeover...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Load Kernel Module configfs...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Load Kernel Module drm...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Load Kernel Module fuse...
Jul 14 15:08:49 Art-ig systemd[1]: Condition check resulted in Set Up Additiona>
Jul 14 15:08:49 Art-ig systemd[1]: Starting File System Check on Root Device...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Journal Service...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Load Kernel Modules...
Jul 14 15:08:49 Art-ig systemd[1]: Condition check resulted in Repartition Root>
Jul 14 15:08:49 Art-ig systemd[1]: Starting Coldplug All udev Devices...
Jul 14 15:08:49 Art-ig systemd[1]: Starting Setup Virtual Console...
Jul 14 15:08:49 Art-ig systemd[1]: Mounted Huge Pages File System.
Jul 14 15:08:49 Art-ig systemd[1]: Mounted POSIX Message Queue File System.
Jul 14 15:08:49 Art-ig systemd[1]: Mounted Kernel Debug File System.
Jul 14 15:08:49 Art-ig systemd[1]: Mounted Kernel Trace File System.
Jul 14 15:08:49 Art-ig systemd[1]: Finished Create list of static device nodes >
Jul 14 15:08:49 Art-ig systemd[1]: modprobe@drm.service: Succeeded.
Jul 14 15:08:49 Art-ig systemd[1]: Finished Load Kernel Module drm.
Jul 14 15:08:49 Art-ig systemd[1]: modprobe@configfs.service: Succeeded.
Jul 14 15:08:49 Art-ig systemd[1]: Finished Load Kernel Module configfs.
Jul 14 15:08:49 Art-ig systemd[1]: Mounting Kernel Configuration File System...
Jul 14 15:08:49 Art-ig systemd[1]: Mounted Kernel Configuration File System.
Jul 14 15:08:49 Art-ig systemd[1]: Started Software RAID Monitor Takeover.
Jul 14 15:08:49 Art-ig kernel: fuse: init (API version 7.32)
Jul 14 15:08:49 Art-ig systemd[1]: modprobe@fuse.service: Succeeded.
Jul 14 15:08:49 Art-ig systemd[1]: Finished Load Kernel Module fuse.
Jul 14 15:08:49 Art-ig systemd[1]: Mounting FUSE Control File System...
Jul 14 15:08:49 Art-ig systemd[1]: Mounted FUSE Control File System.
Jul 14 15:08:49 Art-ig systemd[1]: Started Journal Service.
Jul 14 15:08:49 Art-ig kernel: Non-volatile memory driver v1.3
Jul 14 15:08:49 Art-ig kernel: sd 2:0:0:0: Attached scsi generic sg0 type 0
Jul 14 15:08:49 Art-ig kernel: sd 3:0:0:0: Attached scsi generic sg1 type 0
Jul 14 15:08:49 Art-ig kernel: sr 5:0:0:0: Attached scsi generic sg2 type 5
Jul 14 15:08:49 Art-ig kernel: sr 6:0:0:0: Attached scsi generic sg3 type 5
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda1): re-mounted. Opts: acl
Jul 14 15:08:49 Art-ig kernel: EXT4-fs (sda8): re-mounted. Opts: acl
Jul 14 15:08:51 Art-ig kernel: input: Power Button as /devices/LNXSYSTM:00/LNXS>
Jul 14 15:08:51 Art-ig kernel: ACPI: Power Button [PWRB]
Jul 14 15:08:51 Art-ig kernel: input: Sleep Button as /devices/LNXSYSTM:00/LNXS>
Jul 14 15:08:51 Art-ig kernel: ACPI: Sleep Button [SLPB]
Jul 14 15:08:51 Art-ig kernel: input: Power Button as /devices/LNXSYSTM:00/LNXP>
Jul 14 15:08:51 Art-ig kernel: ACPI: Power Button [PWRF]
Jul 14 15:08:51 Art-ig kernel: thermal LNXTHERM:00: registered as thermal_zone0
Jul 14 15:08:51 Art-ig kernel: ACPI: Thermal Zone [TZ00] (28 C)
Jul 14 15:08:51 Art-ig kernel: thermal LNXTHERM:01: registered as thermal_zone1
Jul 14 15:08:51 Art-ig kernel: ACPI: Thermal Zone [TZ01] (30 C)
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001828->
Jul 14 15:08:51 Art-ig kernel: ACPI: If an ACPI driver is available for this de>
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001C40->
Jul 14 15:08:51 Art-ig kernel: ACPI: If an ACPI driver is available for this de>
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001C30->
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001C30->
Jul 14 15:08:51 Art-ig kernel: ACPI: If an ACPI driver is available for this de>
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001C00->
Jul 14 15:08:51 Art-ig kernel: ACPI Warning: SystemIO range 0x0000000000001C00->
Jul 14 15:08:51 Art-ig kernel: ACPI: If an ACPI driver is available for this de>
Jul 14 15:08:51 Art-ig kernel: lpc_ich: Resource conflict(s) found affecting gp>
Jul 14 15:08:51 Art-ig kernel: i801_smbus 0000:00:1f.3: enabling device (0001 ->
Jul 14 15:08:51 Art-ig kernel: i801_smbus 0000:00:1f.3: SPD Write Disable is set
Jul 14 15:08:51 Art-ig kernel: i801_smbus 0000:00:1f.3: SMBus using PCI interru>
Jul 14 15:08:51 Art-ig kernel: i2c i2c-6: 2/4 memory slots populated (from DMI)
Jul 14 15:08:51 Art-ig kernel: i2c i2c-6: Successfully instantiated SPD at 0x50
Jul 14 15:08:51 Art-ig kernel: i2c i2c-6: Successfully instantiated SPD at 0x52
Jul 14 15:08:52 Art-ig kernel: RAPL PMU: API unit is 2^-32 Joules, 4 fixed coun>
Jul 14 15:08:52 Art-ig kernel: RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
Jul 14 15:08:52 Art-ig kernel: RAPL PMU: hw unit of domain package 2^-14 Joules
Jul 14 15:08:52 Art-ig kernel: RAPL PMU: hw unit of domain dram 2^-14 Joules
Jul 14 15:08:52 Art-ig kernel: RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
Jul 14 15:08:52 Art-ig kernel: snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (>
Jul 14 15:08:52 Art-ig kernel: iTCO_vendor_support: vendor-support=0
Jul 14 15:08:52 Art-ig kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
Jul 14 15:08:52 Art-ig kernel: iTCO_wdt: unable to reset NO_REBOOT flag, device>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel HDMI HDMI/DP,pcm=9 as /devices/>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel HDMI HDMI/DP,pcm=10 as /devices>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2: autoconfig fo>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:    speaker_ou>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:    hp_outs=1 >
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:    mono: mono>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:    dig-out=0x>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:    inputs:
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:      Front Mi>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:      Rear Mic>
Jul 14 15:08:52 Art-ig kernel: snd_hda_codec_realtek hdaudioC1D2:      Line=0x1a
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Front Mic as /devices/pci00>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Rear Mic as /devices/pci000>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Line as /devices/pci0000:00>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Line Out Front as /devices/>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Line Out Surround as /devic>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Line Out CLFE as /devices/p>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Line Out Side as /devices/p>
Jul 14 15:08:52 Art-ig kernel: input: HDA Intel PCH Front Headphone as /devices>
Jul 14 15:08:52 Art-ig kernel: intel_rapl_common: Found RAPL domain package
Jul 14 15:08:52 Art-ig kernel: intel_rapl_common: Found RAPL domain core
Jul 14 15:08:52 Art-ig kernel: intel_rapl_common: Found RAPL domain uncore
Jul 14 15:08:52 Art-ig kernel: intel_rapl_common: Found RAPL domain dram
Jul 14 15:08:52 Art-ig kernel: r8169 0000:02:00.0: can't disable ASPM; OS doesn>
Jul 14 15:08:52 Art-ig kernel: libphy: r8169: probed
Jul 14 15:08:52 Art-ig kernel: r8169 0000:02:00.0 eth0: RTL8168g/8111g, 40:8d:5>
Jul 14 15:08:52 Art-ig kernel: r8169 0000:02:00.0 eth0: jumbo features [frames:>
Jul 14 15:08:52 Art-ig kernel: r8169 0000:02:00.0 enp2s0: renamed from eth0
Jul 14 15:08:53 Art-ig kernel: cfg80211: Loading compiled-in X.509 certificates>
Jul 14 15:08:53 Art-ig kernel: cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf4>
Jul 14 15:08:53 Art-ig kernel: Adding 4087272k swap on /dev/sda5.  Priority:-2 >
Jul 14 15:08:53 Art-ig kernel: ath5k 0000:04:00.0: registered as 'phy0'
Jul 14 15:08:54 Art-ig kernel: ath: EEPROM regdomain: 0x809c
Jul 14 15:08:54 Art-ig kernel: ath: EEPROM indicates we should expect a country>
Jul 14 15:08:54 Art-ig kernel: ath: doing EEPROM country->regdmn map search
Jul 14 15:08:54 Art-ig kernel: ath: country maps to regdmn code: 0x52
Jul 14 15:08:54 Art-ig kernel: ath: Country alpha2 being used: CN
Jul 14 15:08:54 Art-ig kernel: ath: Regpair used: 0x52
Jul 14 15:08:54 Art-ig kernel: ieee80211 phy0: Selected rate control algorithm >
Jul 14 15:08:54 Art-ig kernel: ath5k: phy0: Atheros AR2414 chip found (MAC: 0x7>
Jul 14 15:08:54 Art-ig kernel: ath5k 0000:04:00.0 wlp4s0: renamed from wlan0
Jul 14 15:08:54 Art-ig kernel: device-mapper: uevent: version 1.0.3
Jul 14 15:08:54 Art-ig kernel: device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) >
Jul 14 15:08:55 Art-ig kernel: EXT4-fs (sdb5): mounted filesystem with ordered >
Jul 14 15:08:56 Art-ig kernel: EXT4-fs (sdb1): mounted filesystem with ordered >
Jul 14 15:08:56 Art-ig kernel: EXT4-fs (sda7): mounted filesystem with ordered >
Jul 14 15:08:58 Art-ig kernel: EXT4-fs (sda6): mounted filesystem with ordered >
Jul 14 15:08:58 Art-ig kernel: EXT4-fs (sda9): mounted filesystem with ordered >
Jul 14 15:09:03 Art-ig kernel: vboxdrv: loading out-of-tree module taints kerne>
Jul 14 15:09:03 Art-ig kernel: vboxdrv: Found 4 processor cores
Jul 14 15:09:03 Art-ig kernel: vboxdrv: TSC mode is Invariant, tentative freque>
Jul 14 15:09:03 Art-ig kernel: vboxdrv: Successfully loaded version 6.1.22_Mage>
Jul 14 15:09:03 Art-ig kernel: VBoxNetFlt: Successfully started.
Jul 14 15:09:03 Art-ig kernel: VBoxNetAdp: Successfully started.
Jul 14 15:09:08 Art-ig kernel: Generic FE-GE Realtek PHY r8169-200:00: attached>
Jul 14 15:09:08 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 15:09:10 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/>
Jul 14 15:09:10 Art-ig kernel: IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link beco>
Jul 14 15:09:12 Art-ig kernel: NET: Registered protocol family 17
Jul 14 15:09:14 Art-ig kernel: wlp4s0: authenticate with 64:70:02:f7:01:6e
Jul 14 15:09:14 Art-ig kernel: wlp4s0: send auth to 64:70:02:f7:01:6e (try 1/3)
Jul 14 15:09:14 Art-ig kernel: wlp4s0: authenticated
Jul 14 15:09:14 Art-ig kernel: wlp4s0: associate with 64:70:02:f7:01:6e (try 1/>
Jul 14 15:09:14 Art-ig kernel: wlp4s0: RX AssocResp from 64:70:02:f7:01:6e (cap>
Jul 14 15:09:14 Art-ig kernel: wlp4s0: associated
Jul 14 15:09:14 Art-ig kernel: IPv6: ADDRCONF(NETDEV_CHANGE): wlp4s0: link beco>
Jul 14 15:09:17 Art-ig kernel: netfilter PSD loaded - (c) astaro AG
Jul 14 15:09:17 Art-ig kernel: IFWLOG: register target
Jul 14 15:10:00 Art-ig kernel: traps: light-locker[6907] trap int3 ip:7f61c3e76>
Jul 14 15:10:12 Art-ig kernel: ISO 9660 Extensions: Microsoft Joliet Level 3
Jul 14 15:10:12 Art-ig kernel: ISO 9660 Extensions: RRIP_1991A
Jul 14 15:12:51 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:52 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:54 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:58 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:00 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:01 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:03 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:07 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:14:59 Art-ig kernel: PM: suspend entry (deep)
Jul 14 15:14:59 Art-ig kernel: Filesystems sync: 0.261 seconds
Jul 14 16:52:39 Art-ig kernel: Freezing user space processes ... (elapsed 0.001>
Jul 14 16:52:39 Art-ig kernel: OOM killer disabled.
Jul 14 16:52:39 Art-ig kernel: Freezing remaining freezable tasks ... (elapsed >
Jul 14 16:52:39 Art-ig kernel: printk: Suspending console(s) (use no_console_su>
Jul 14 16:52:39 Art-ig kernel: wlp4s0: deauthenticating from 64:70:02:f7:01:6e >
Jul 14 16:52:39 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Synchronizing SCSI cache
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Synchronizing SCSI cache
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Stopping disk
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Stopping disk
Jul 14 16:52:39 Art-ig kernel: ACPI: Preparing to enter system sleep state S3
Jul 14 16:52:39 Art-ig kernel: PM: Saving platform NVS memory
Jul 14 16:52:39 Art-ig kernel: Disabling non-boot CPUs ...
Jul 14 16:52:39 Art-ig kernel: IRQ 23: no longer affine to CPU1
Jul 14 16:52:39 Art-ig kernel: IRQ 30: no longer affine to CPU1
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 1 is now offline
Jul 14 16:52:39 Art-ig kernel: IRQ 16: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: IRQ 19: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: IRQ 29: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 2 is now offline
Jul 14 16:52:39 Art-ig kernel: IRQ 31: no longer affine to CPU3
Jul 14 16:52:39 Art-ig kernel: IRQ 35: no longer affine to CPU3
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 3 is now offline
Jul 14 16:52:39 Art-ig kernel: ACPI: Low-level resume complete
Jul 14 16:52:39 Art-ig kernel: PM: Restoring platform NVS memory
Jul 14 16:52:39 Art-ig kernel: smpboot: Scheduler frequency invariance went wob>
Jul 14 16:52:39 Art-ig kernel: Enabling non-boot CPUs ...
Jul 14 16:52:39 Art-ig kernel: x86: Booting SMP configuration:
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 1 APIC 0x2
Jul 14 16:52:39 Art-ig kernel: CPU1 is up
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 2 APIC 0x4
Jul 14 16:52:39 Art-ig kernel: CPU2 is up
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 3 APIC 0x6
Jul 14 16:52:39 Art-ig kernel: CPU3 is up
Jul 14 16:52:39 Art-ig kernel: ACPI: Waking up from system sleep state S3
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Starting disk
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Starting disk
Jul 14 16:52:39 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:39 Art-ig kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SContro>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 16:52:39 Art-ig kernel: ata6.00: configured for UDMA/100
Jul 14 16:52:39 Art-ig kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SContro>
Jul 14 16:52:39 Art-ig kernel: ata3.00: configured for UDMA/133
Jul 14 16:52:39 Art-ig kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SContro>
Jul 14 16:52:39 Art-ig kernel: ata4.00: configured for UDMA/133
Jul 14 16:52:39 Art-ig kernel: OOM killer enabled.
Jul 14 16:52:39 Art-ig kernel: Restarting tasks ...
Jul 14 16:52:39 Art-ig kernel: pci_bus 0000:04: Allocating resources
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: bridge window [io  0x1000-0x0f>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: bridge window [mem 0x00100000->
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  >
Jul 14 16:52:39 Art-ig kernel: done.
Jul 14 16:52:39 Art-ig kernel: video LNXVIDEO:00: Restoring backlight state
Jul 14 16:52:39 Art-ig kernel: PM: suspend exit
Jul 14 16:52:40 Art-ig kernel: wlp4s0: authenticate with 64:70:02:f7:01:6e
Jul 14 16:52:40 Art-ig kernel: wlp4s0: send auth to 64:70:02:f7:01:6e (try 1/3)
Jul 14 16:52:40 Art-ig kernel: wlp4s0: authenticated
Jul 14 16:52:40 Art-ig kernel: wlp4s0: associate with 64:70:02:f7:01:6e (try 1/>
Jul 14 16:52:40 Art-ig kernel: wlp4s0: RX AssocResp from 64:70:02:f7:01:6e (cap>
Jul 14 16:52:40 Art-ig kernel: wlp4s0: associated
Jul 14 16:52:46 Art-ig kernel: Generic FE-GE Realtek PHY r8169-200:00: attached>
Jul 14 16:52:46 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:50 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/>
Jul 14 16:52:50 Art-ig kernel: IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link beco>
lines 993-1015/1015 (END)



ich poste den kompletten Eintrag, den ich mit
Code: Alles auswählen
journalctl -b --dmesg
seit dem letzten Start aus dem Bereitschaftsmodus erhalten habe.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 16:17
von ikseran
und hier die Ausgabe von journalctl -b

Code: Alles auswählen
Jul 14 15:09:13 Art-ig systemd-sysctl[1787]: Not setting net/ipv4/conf/default/>
Jul 14 15:09:13 Art-ig systemd-sysctl[1787]: Not setting net/ipv4/conf/all/prom>
Jul 14 15:09:13 Art-ig systemd-sysctl[1787]: Not setting net/ipv4/conf/default/>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Control process exited, cod>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Failed with result 'exit-co>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1355 (ifplugd)>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1356 (ifup-pos>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1473 (dhclient>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1703 (run-part>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1763 (vnstat_i>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1765 (wpa_supp>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1767 (ifplugd)>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Unit process 1774 (vnstat_i>
Jul 14 15:09:13 Art-ig systemd[1]: Failed to start LSB: Bring up/down networkin>
Jul 14 15:09:13 Art-ig systemd[1]: network.service: Consumed 1.090s CPU time.
Jul 14 15:09:13 Art-ig ifplugd(enp2s0)[1355]: client: Unknown parameter "-r". U>
Jul 14 15:09:13 Art-ig network-up[885]: Warten bis das Netzwerk gestartet ist[ >
Jul 14 15:09:13 Art-ig systemd[1]: Started LSB: Wait for the hotplugged network>
Jul 14 15:09:13 Art-ig systemd[1]: Reached target Network.
Jul 14 15:09:13 Art-ig systemd[1]: Reached target Network is Online.
Jul 14 15:09:13 Art-ig systemd[1]: Reached target Host and Network Name Lookups.
Jul 14 15:09:13 Art-ig systemd[1]: Starting CUPS Scheduler...
Jul 14 15:09:13 Art-ig systemd[1]: Starting LSB: Starts the postfix daemons...
Jul 14 15:09:13 Art-ig systemd[1]: Starting Shorewall IPv4 firewall...
Jul 14 15:09:13 Art-ig systemd[1]: Starting Permit User Sessions...
Jul 14 15:09:14 Art-ig udisksd[905]: Acquired the name org.freedesktop.UDisks2 >
Jul 14 15:09:14 Art-ig kernel: wlp4s0: authenticate with 64:70:02:f7:01:6e
Jul 14 15:09:14 Art-ig kernel: wlp4s0: send auth to 64:70:02:f7:01:6e (try 1/3)
Jul 14 15:09:14 Art-ig kernel: wlp4s0: authenticated
Jul 14 15:09:14 Art-ig kernel: wlp4s0: associate with 64:70:02:f7:01:6e (try 1/>
Jul 14 15:09:14 Art-ig kernel: wlp4s0: RX AssocResp from 64:70:02:f7:01:6e (cap>
Jul 14 15:09:14 Art-ig kernel: wlp4s0: associated
Jul 14 15:09:14 Art-ig kernel: IPv6: ADDRCONF(NETDEV_CHANGE): wlp4s0: link beco>
Jul 14 15:09:14 Art-ig ifplugd(wlp4s0)[1767]: Link beat detected.
Jul 14 15:09:14 Art-ig systemd[1]: Finished Permit User Sessions.
Jul 14 15:09:14 Art-ig systemd[1]: Started Command Scheduler.
Jul 14 15:09:14 Art-ig systemd[1]: Starting Hold until boot process finishes up>
Jul 14 15:09:14 Art-ig systemd[1]: Starting Terminate Plymouth Boot Screen...
Jul 14 15:09:14 Art-ig ifplugd(enp2s0)[1355]: client:  [  OK  ]
Jul 14 15:09:14 Art-ig ifplugd(enp2s0)[1355]: Program executed successfully.
Jul 14 15:09:14 Art-ig systemd[1]: Received SIGRTMIN+21 from PID 317 (plymouthd>
Jul 14 15:09:14 Art-ig systemd[1]: Received SIGRTMIN+21 from PID 317 (plymouthd>
Jul 14 15:09:14 Art-ig systemd[1]: Finished Hold until boot process finishes up.
Jul 14 15:09:14 Art-ig systemd[1]: Finished Terminate Plymouth Boot Screen.
Jul 14 15:09:14 Art-ig systemd[1]: Started LXDM (Lightweight X11 Display Manage>
Jul 14 15:09:14 Art-ig crond[1858]: (CRON) STARTUP (1.5.5)
Jul 14 15:09:14 Art-ig crond[1858]: (CRON) INFO (RANDOM_DELAY will be scaled wi>
Jul 14 15:09:15 Art-ig crond[1858]: (CRON) INFO (running with inotify support)
Jul 14 15:09:15 Art-ig shorewall[1875]: Starting Shorewall....
Jul 14 15:09:15 Art-ig shorewall[1875]: Initializing...
Jul 14 15:09:15 Art-ig ifplugd(wlp4s0)[1767]: Executing '/etc/ifplugd/ifplugd.a>
Jul 14 15:09:15 Art-ig dbus-daemon[875]: [system] Activating via systemd: servi>
Jul 14 15:09:15 Art-ig dhclient[1946]: DHCPDISCOVER on wlp4s0 to 255.255.255.25>
Jul 14 15:09:15 Art-ig systemd[1]: Starting Manage, Install and Generate Color >
Jul 14 15:09:16 Art-ig shorewall[1875]: Processing /etc/shorewall/init ...
Jul 14 15:09:16 Art-ig shorewall[1875]: Processing /etc/shorewall/tcclear ...
Jul 14 15:09:16 Art-ig shorewall[1875]: Setting up Route Filtering...
Jul 14 15:09:16 Art-ig shorewall[1875]: Setting up Martian Logging...
Jul 14 15:09:16 Art-ig shorewall[1875]: Setting up Proxy ARP...
Jul 14 15:09:16 Art-ig shorewall[1875]: Preparing iptables-restore input...
Jul 14 15:09:16 Art-ig shorewall[1875]: Running /sbin/iptables-restore --wait 6>
Jul 14 15:09:16 Art-ig dbus-daemon[875]: [system] Successfully activated servic>
Jul 14 15:09:16 Art-ig systemd[1]: Started Manage, Install and Generate Color P>
Jul 14 15:09:16 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 15:09:16 Art-ig avahi-daemon[874]: New relevant interface wlp4s0.IPv6 fo>
Jul 14 15:09:16 Art-ig avahi-daemon[874]: Registering new address record for fe>
Jul 14 15:09:16 Art-ig acpid[872]: client connected from 1889[0:0]
Jul 14 15:09:16 Art-ig acpid[872]: 1 client rule loaded
Jul 14 15:09:16 Art-ig dhclient[1946]: DHCPOFFER of 192.168.0.101 from 192.168.>
Jul 14 15:09:16 Art-ig dhclient[1946]: DHCPREQUEST for 192.168.0.101 on wlp4s0 >
Jul 14 15:09:16 Art-ig dhclient[1946]: DHCPACK of 192.168.0.101 from 192.168.0.1
Jul 14 15:09:16 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 15:09:16 Art-ig avahi-daemon[874]: New relevant interface wlp4s0.IPv4 fo>
Jul 14 15:09:16 Art-ig avahi-daemon[874]: Registering new address record for 19>
Jul 14 15:09:17 Art-ig shorewall[1875]: Processing /etc/shorewall/start ...
Jul 14 15:09:17 Art-ig systemd[1]: Started CUPS Scheduler.
Jul 14 15:09:17 Art-ig dhclient[1946]: bound to 192.168.0.101 -- renewal in 328>
Jul 14 15:09:17 Art-ig ifplugd(wlp4s0)[1767]: client: Determining IP informatio>
Jul 14 15:09:17 Art-ig ifplugd(wlp4s0)[1767]: Program executed successfully.
Jul 14 15:09:17 Art-ig acpid[872]: client connected from 1889[0:0]
Jul 14 15:09:17 Art-ig acpid[872]: 1 client rule loaded
Jul 14 15:09:17 Art-ig kernel: netfilter PSD loaded - (c) astaro AG
Jul 14 15:09:17 Art-ig kernel: IFWLOG: register target
Jul 14 15:09:17 Art-ig shorewall[1875]: Processing /etc/shorewall/started ...
Jul 14 15:09:17 Art-ig root[2237]: Shorewall started
Jul 14 15:09:17 Art-ig shorewall[1875]: done.
Jul 14 15:09:17 Art-ig systemd[1]: Finished Shorewall IPv4 firewall.
Jul 14 15:09:18 Art-ig systemd[1]: Starting Shorewall IPv6 firewall...
Jul 14 15:09:18 Art-ig shorewall[2275]: Starting Shorewall6....
Jul 14 15:09:18 Art-ig shorewall[2275]: Initializing...
Jul 14 15:09:18 Art-ig shorewall[2275]: Processing /etc/shorewall6/init ...
Jul 14 15:09:18 Art-ig shorewall[2275]: Setting up Proxy NDP...
Jul 14 15:09:18 Art-ig shorewall[2275]: Preparing ip6tables-restore input...
Jul 14 15:09:18 Art-ig shorewall[2275]: Running /sbin/ip6tables-restore --wait >
Jul 14 15:09:19 Art-ig shorewall[2275]: Processing /etc/shorewall6/start ...
Jul 14 15:09:19 Art-ig shorewall[2275]: Processing /etc/shorewall6/started ...
Jul 14 15:09:19 Art-ig root[2342]: Shorewall6 started
Jul 14 15:09:19 Art-ig shorewall[2275]: done.
Jul 14 15:09:19 Art-ig systemd[1]: Finished Shorewall IPv6 firewall.
Jul 14 15:09:43 Art-ig dbus-daemon[6626]: [session uid=0 pid=6062] Activating s>
Jul 14 15:09:43 Art-ig dbus-daemon[6626]: [session uid=0 pid=6062] Successfully>
Jul 14 15:09:46 Art-ig org.a11y.Bus[6633]: dbus-daemon[6633]: Activating servic>
Jul 14 15:09:46 Art-ig org.a11y.Bus[6633]: dbus-daemon[6633]: Successfully acti>
Jul 14 15:09:46 Art-ig org.a11y.Bus[6640]: SpiRegistry daemon is running with w>
Jul 14 15:09:48 Art-ig postfix/postfix-script[6669]: starting the Postfix mail >
Jul 14 15:09:48 Art-ig postfix/master[6671]: daemon started -- version 3.5.9, c>
Jul 14 15:09:48 Art-ig postfix[1807]: postfix-Dienst wird gestartet: /etc/rc.d/>
Jul 14 15:09:48 Art-ig postfix[1807]: [  OK  ]
Jul 14 15:09:48 Art-ig systemd[1]: Started LSB: Starts the postfix daemons.
Jul 14 15:09:48 Art-ig systemd[1]: Reached target Multi-User System.
Jul 14 15:09:48 Art-ig systemd[1]: Reached target Graphical Interface.
Jul 14 15:09:48 Art-ig systemd[1]: Starting Update UTMP about System Runlevel C>
Jul 14 15:09:48 Art-ig systemd[1]: systemd-update-utmp-runlevel.service: Succee>
Jul 14 15:09:48 Art-ig systemd[1]: Finished Update UTMP about System Runlevel C>
Jul 14 15:09:48 Art-ig systemd[1]: Startup finished in 4.893s (kernel) + 1min 4>
Jul 14 15:09:51 Art-ig lxdm-session[6679]: gkr-pam: unable to locate daemon con>
Jul 14 15:09:51 Art-ig lxdm-session[6679]: gkr-pam: stashed password to try lat>
Jul 14 15:09:51 Art-ig lxdm-session[6679]: gkr-pam: unable to locate daemon con>
Jul 14 15:09:51 Art-ig lxdm-session[6679]: gkr-pam: gnome-keyring-daemon starte>
Jul 14 15:09:51 Art-ig systemd[1]: Created slice User Slice of UID 500.
Jul 14 15:09:51 Art-ig systemd[1]: Starting User Runtime Directory /run/user/50>
Jul 14 15:09:51 Art-ig systemd-logind[899]: New session c1 of user walter.
Jul 14 15:09:51 Art-ig systemd[1]: Finished User Runtime Directory /run/user/50>
Jul 14 15:09:51 Art-ig systemd[1]: Starting User Manager for UID 500...
Jul 14 15:09:52 Art-ig systemd-xdg-autostart-generator[6697]: Exec binary '/usr>
Jul 14 15:09:52 Art-ig systemd-xdg-autostart-generator[6697]: Not generating se>
Jul 14 15:09:52 Art-ig systemd[6688]: Queued start job for default target Main >
Jul 14 15:09:52 Art-ig systemd[6688]: Reached target Paths.
Jul 14 15:09:52 Art-ig systemd[6688]: Reached target Timers.
Jul 14 15:09:52 Art-ig systemd[6688]: Starting D-Bus User Message Bus Socket.
Jul 14 15:09:52 Art-ig systemd[6688]: Listening on GnuPG cryptographic agent an>
Jul 14 15:09:52 Art-ig systemd[6688]: Listening on Sound System.
Jul 14 15:09:52 Art-ig systemd[6688]: Listening on D-Bus User Message Bus Socke>
Jul 14 15:09:52 Art-ig systemd[6688]: Reached target Sockets.
Jul 14 15:09:52 Art-ig systemd[6688]: Reached target Basic System.
Jul 14 15:09:52 Art-ig systemd[1]: Started User Manager for UID 500.
Jul 14 15:09:52 Art-ig systemd[6688]: Started GnuPG cryptographic agent and pas>
Jul 14 15:09:52 Art-ig systemd[6688]: Reached target Main User Target.
Jul 14 15:09:52 Art-ig systemd[6688]: Startup finished in 898ms.
Jul 14 15:09:52 Art-ig systemd[1]: Started Session c1 of user walter.
Jul 14 15:09:52 Art-ig lxdm-session[6679]: pam_unix(lxdm:session): session open>
Jul 14 15:09:52 Art-ig gpg-agent[6699]: gpg-agent (GnuPG) 2.2.27 starting in su>
Jul 14 15:09:52 Art-ig gpg-agent[6699]: using fd 3 for std socket (/run/user/50>
Jul 14 15:09:52 Art-ig gpg-agent[6699]: listening on: std=3 extra=-1 browser=-1>
Jul 14 15:09:52 Art-ig dbus-daemon[875]: [system] Activating via systemd: servi>
Jul 14 15:09:52 Art-ig systemd[1]: Starting Hostname Service...
Jul 14 15:09:52 Art-ig dbus-daemon[875]: [system] Successfully activated servic>
Jul 14 15:09:52 Art-ig systemd[1]: Started Hostname Service.
Jul 14 15:09:53 Art-ig systemd[6688]: Starting Sound Service...
Jul 14 15:09:54 Art-ig rtkit-daemon[898]: Successfully made thread 6752 of proc>
Jul 14 15:09:54 Art-ig rtkit-daemon[898]: Supervising 1 threads of 1 processes >
Jul 14 15:09:54 Art-ig systemd[6688]: Starting D-Bus User Message Bus...
Jul 14 15:09:54 Art-ig systemd[6688]: Started D-Bus User Message Bus.
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Supervising 1 threads of 1 processes >
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Successfully made thread 6754 of proc>
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Supervising 2 threads of 1 processes >
Jul 14 15:09:55 Art-ig dbus-daemon[875]: [system] Activating via systemd: servi>
Jul 14 15:09:55 Art-ig systemd[1]: Condition check resulted in Bluetooth servic>
Jul 14 15:09:55 Art-ig pulseaudio[6752]: module-combine is deprecated: Please u>
Jul 14 15:09:55 Art-ig pulseaudio[6752]: We will now load module-combine-sink. >
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Supervising 2 threads of 1 processes >
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Successfully made thread 6760 of proc>
Jul 14 15:09:55 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:09:55 Art-ig systemd[6688]: Started Sound Service.
Jul 14 15:09:56 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:09:56 Art-ig systemd[6688]: Starting Virtual filesystem service...
Jul 14 15:09:56 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:09:56 Art-ig systemd[6688]: Started Virtual filesystem service.
Jul 14 15:09:57 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:09:57 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:09:58 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:09:58 Art-ig systemd[6688]: Starting Virtual filesystem service - dis>
Jul 14 15:09:58 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:09:58 Art-ig systemd[6688]: Started Virtual filesystem service - disk>
Jul 14 15:09:58 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:09:58 Art-ig systemd[6688]: Starting Virtual filesystem service - Med>
Jul 14 15:09:58 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:09:58 Art-ig systemd[6688]: Started Virtual filesystem service - Medi>
Jul 14 15:09:59 Art-ig gnome-keyring-daemon[6684]: The Secret Service was alrea>
Jul 14 15:09:59 Art-ig polkitd[1212]: Registered Authentication Agent for unix->
Jul 14 15:10:00 Art-ig mate-session[6701]: WARNING: Could not launch applicatio>
Jul 14 15:10:00 Art-ig gnome-keyring-daemon[6684]: The PKCS#11 component was al>
Jul 14 15:10:00 Art-ig gnome-keyring-daemon[6684]: The SSH agent was already in>
Jul 14 15:10:00 Art-ig kernel: traps: light-locker[6907] trap int3 ip:7f61c3e76>
Jul 14 15:10:00 Art-ig net_applet[6910]: ### Program is starting ###
Jul 14 15:10:00 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:00 Art-ig mgaapplet[6917]: ### Program is starting ###
Jul 14 15:10:00 Art-ig systemd[6688]: Starting Portal service...
Jul 14 15:10:02 Art-ig net_applet[6910]: failed to acquire monitor on DBus: org>
                                          (is mandi started?)
Jul 14 15:10:02 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:02 Art-ig systemd[6688]: Starting Evolution source registry...
Jul 14 15:10:03 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:03 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:03 Art-ig goa-daemon[10524]: goa-daemon version 3.38.0 starting
Jul 14 15:10:03 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:03 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:03 Art-ig systemd[6688]: Starting Bluetooth OBEX service...
Jul 14 15:10:03 Art-ig obexd[10538]: OBEX daemon 5.55
Jul 14 15:10:03 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:03 Art-ig systemd[6688]: Started Bluetooth OBEX service.
Jul 14 15:10:04 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:04 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:04 Art-ig systemd[6688]: Starting flatpak document portal service.>
Jul 14 15:10:04 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:04 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:04 Art-ig systemd[6688]: Started Evolution source registry.
Jul 14 15:10:04 Art-ig systemd[6688]: Starting sandboxed app permission store...
Jul 14 15:10:05 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:05 Art-ig systemd[6688]: Started sandboxed app permission store.
Jul 14 15:10:05 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:05 Art-ig systemd[6688]: Started flatpak document portal service.
Jul 14 15:10:05 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:05 Art-ig systemd[6688]: Starting Portal service (GTK+/GNOME imple>
Jul 14 15:10:05 Art-ig xdg-desktop-por[10568]: Theme parsing error: gtk.css:2:3>
Jul 14 15:10:05 Art-ig xdg-desktop-por[10568]: Couldn't register with accessibi>
Jul 14 15:10:05 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:05 Art-ig systemd[6688]: Started Portal service (GTK+/GNOME implem>
Jul 14 15:10:05 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:05 Art-ig systemd[6688]: Starting Evolution calendar service...
Jul 14 15:10:06 Art-ig xdg-desktop-por[6932]: Failed connect to PipeWire: Could>
Jul 14 15:10:06 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:06 Art-ig systemd[6688]: Started Portal service.
Jul 14 15:10:06 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:06 Art-ig systemd[6688]: Started Evolution calendar service.
Jul 14 15:10:06 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:06 Art-ig systemd[6688]: Starting Evolution address book service...
Jul 14 15:10:06 Art-ig caja[6853]: [N-A] Caja-Actions Menu Extender 1.8.3 initi>
Jul 14 15:10:06 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:06 Art-ig systemd[6688]: Started Evolution address book service.
Jul 14 15:10:08 Art-ig caja[6853]: [N-A] Caja-Actions Tracker 1.8.3 initializin>
Jul 14 15:10:10 Art-ig mgaapplet[6917]: running: ionice -p 6917 -n7
Jul 14 15:10:12 Art-ig kernel: ISO 9660 Extensions: Microsoft Joliet Level 3
Jul 14 15:10:12 Art-ig kernel: ISO 9660 Extensions: RRIP_1991A
Jul 14 15:10:12 Art-ig udisksd[905]: Mounted /dev/sr1 at /run/media/walter/Seal>
Jul 14 15:10:12 Art-ig udisksd[905]: udisks_state_check_mounted_fs_entry: block>
Jul 14 15:10:20 Art-ig dbus-daemon[875]: [system] Failed to activate service 'o>
Jul 14 15:10:20 Art-ig pulseaudio[6752]: GetManagedObjects() failed: org.freede>
Jul 14 15:10:22 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:22 Art-ig mate-multiload-[10679]: Theme parsing error: gtk.css:2:3>
Jul 14 15:10:22 Art-ig mate-multiload-[10679]: Couldn't register with accessibi>
Jul 14 15:10:22 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:22 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:22 Art-ig systemd[6688]: Starting Virtual filesystem metadata serv>
Jul 14 15:10:22 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:22 Art-ig systemd[6688]: Started Virtual filesystem metadata servi>
Jul 14 15:10:22 Art-ig dbus-daemon[875]: [system] Activating service name='org.>
Jul 14 15:10:22 Art-ig dbus-daemon[875]: [system] Successfully activated servic>
Jul 14 15:10:28 Art-ig systemd[1]: systemd-hostnamed.service: Succeeded.
Jul 14 15:10:32 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Activating>
Jul 14 15:10:32 Art-ig systemd[6688]: Starting Accessibility services bus...
Jul 14 15:10:32 Art-ig dbus-daemon[6753]: [session uid=500 pid=6753] Successful>
Jul 14 15:10:32 Art-ig systemd[6688]: Started Accessibility services bus.
Jul 14 15:10:36 Art-ig xdg-desktop-por[6932]: Failed to get application states:>
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 3 threads of 1 processes >
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Successfully made thread 23875 of pro>
Jul 14 15:11:44 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:45 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:45 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:47 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:47 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:49 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:11:49 Art-ig rtkit-daemon[898]: Supervising 4 threads of 2 processes >
Jul 14 15:12:51 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:52 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:54 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:12:58 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:00 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:01 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:03 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:13:07 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 15:14:59 Art-ig mate-session[6701]: WARNING: Couldn't lock screen: Kindp>
Jul 14 15:14:59 Art-ig ModemManager[869]: <info>  [sleep-monitor] system is abo>
Jul 14 15:14:59 Art-ig systemd[1]: Reached target Sleep.
Jul 14 15:14:59 Art-ig systemd[1]: Starting Suspend...
Jul 14 15:14:59 Art-ig systemd-sleep[51800]: Suspending system...
Jul 14 15:14:59 Art-ig kernel: PM: suspend entry (deep)
Jul 14 15:14:59 Art-ig kernel: Filesystems sync: 0.261 seconds
Jul 14 16:52:39 Art-ig kernel: Freezing user space processes ... (elapsed 0.001>
Jul 14 16:52:39 Art-ig kernel: OOM killer disabled.
Jul 14 16:52:39 Art-ig kernel: Freezing remaining freezable tasks ... (elapsed >
Jul 14 16:52:39 Art-ig kernel: printk: Suspending console(s) (use no_console_su>
Jul 14 16:52:39 Art-ig kernel: wlp4s0: deauthenticating from 64:70:02:f7:01:6e >
Jul 14 16:52:39 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Synchronizing SCSI cache
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Synchronizing SCSI cache
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Stopping disk
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Stopping disk
Jul 14 16:52:39 Art-ig kernel: ACPI: Preparing to enter system sleep state S3
Jul 14 16:52:39 Art-ig kernel: PM: Saving platform NVS memory
Jul 14 16:52:39 Art-ig kernel: Disabling non-boot CPUs ...
Jul 14 16:52:39 Art-ig kernel: IRQ 23: no longer affine to CPU1
Jul 14 16:52:39 Art-ig kernel: IRQ 30: no longer affine to CPU1
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 1 is now offline
Jul 14 16:52:39 Art-ig kernel: IRQ 16: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: IRQ 19: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: IRQ 29: no longer affine to CPU2
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 2 is now offline
Jul 14 16:52:39 Art-ig kernel: IRQ 31: no longer affine to CPU3
Jul 14 16:52:39 Art-ig kernel: IRQ 35: no longer affine to CPU3
Jul 14 16:52:39 Art-ig kernel: smpboot: CPU 3 is now offline
Jul 14 16:52:39 Art-ig kernel: ACPI: Low-level resume complete
Jul 14 16:52:39 Art-ig kernel: PM: Restoring platform NVS memory
Jul 14 16:52:39 Art-ig kernel: smpboot: Scheduler frequency invariance went wob>
Jul 14 16:52:39 Art-ig kernel: Enabling non-boot CPUs ...
Jul 14 16:52:39 Art-ig kernel: x86: Booting SMP configuration:
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 1 APIC 0x2
Jul 14 16:52:39 Art-ig kernel: CPU1 is up
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 2 APIC 0x4
Jul 14 16:52:39 Art-ig kernel: CPU2 is up
Jul 14 16:52:39 Art-ig kernel: smpboot: Booting Node 0 Processor 3 APIC 0x6
Jul 14 16:52:39 Art-ig kernel: CPU3 is up
Jul 14 16:52:39 Art-ig kernel: ACPI: Waking up from system sleep state S3
Jul 14 16:52:39 Art-ig kernel: sd 2:0:0:0: [sda] Starting disk
Jul 14 16:52:39 Art-ig kernel: sd 3:0:0:0: [sdb] Starting disk
Jul 14 16:52:39 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:39 Art-ig kernel: ata6: SATA link up 1.5 Gbps (SStatus 113 SContro>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEAT>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY>
Jul 14 16:52:39 Art-ig kernel: ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE C>
Jul 14 16:52:39 Art-ig kernel: ata6.00: configured for UDMA/100
Jul 14 16:52:39 Art-ig kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SContro>
Jul 14 16:52:39 Art-ig kernel: ata3.00: configured for UDMA/133
Jul 14 16:52:39 Art-ig kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SContro>
Jul 14 16:52:39 Art-ig kernel: ata4.00: configured for UDMA/133
Jul 14 16:52:39 Art-ig kernel: OOM killer enabled.
Jul 14 16:52:39 Art-ig kernel: Restarting tasks ...
Jul 14 16:52:39 Art-ig kernel: pci_bus 0000:04: Allocating resources
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: bridge window [io  0x1000-0x0f>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: bridge window [mem 0x00100000->
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: no space for [mem size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 15: failed to assign [mem >
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: no space for [io  size>
Jul 14 16:52:39 Art-ig kernel: pci 0000:03:00.0: BAR 13: failed to assign [io  >
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: The canary thread is apparently starv>
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: Demoting known real-time threads.
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: Successfully demoted thread 6760 of p>
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: Successfully demoted thread 6754 of p>
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: Successfully demoted thread 6752 of p>
Jul 14 16:52:39 Art-ig rtkit-daemon[898]: Demoted 3 threads.
Jul 14 16:52:39 Art-ig systemd-sleep[51800]: System resumed.
Jul 14 16:52:39 Art-ig kernel: done.
Jul 14 16:52:39 Art-ig kernel: video LNXVIDEO:00: Restoring backlight state
Jul 14 16:52:39 Art-ig kernel: PM: suspend exit
Jul 14 16:52:39 Art-ig systemd[1]: systemd-suspend.service: Succeeded.
Jul 14 16:52:39 Art-ig systemd[1]: Finished Suspend.
Jul 14 16:52:39 Art-ig systemd[1]: Stopped target Sleep.
Jul 14 16:52:39 Art-ig systemd[1]: Reached target Suspend.
Jul 14 16:52:39 Art-ig systemd[1]: Stopped target Suspend.
Jul 14 16:52:39 Art-ig systemd-logind[899]: Operation 'sleep' finished.
Jul 14 16:52:39 Art-ig ModemManager[869]: <info>  [sleep-monitor] system is res>
Jul 14 16:52:39 Art-ig ifplugd(wlp4s0)[1767]: Link beat lost.
Jul 14 16:52:40 Art-ig ifplugd(enp2s0)[1355]: Link beat lost.
Jul 14 16:52:40 Art-ig kernel: wlp4s0: authenticate with 64:70:02:f7:01:6e
Jul 14 16:52:40 Art-ig kernel: wlp4s0: send auth to 64:70:02:f7:01:6e (try 1/3)
Jul 14 16:52:40 Art-ig kernel: wlp4s0: authenticated
Jul 14 16:52:40 Art-ig kernel: wlp4s0: associate with 64:70:02:f7:01:6e (try 1/>
Jul 14 16:52:40 Art-ig kernel: wlp4s0: RX AssocResp from 64:70:02:f7:01:6e (cap>
Jul 14 16:52:40 Art-ig kernel: wlp4s0: associated
Jul 14 16:52:40 Art-ig ifplugd(wlp4s0)[1767]: Link beat detected.
Jul 14 16:52:42 Art-ig ModemManager[869]: <info>  [base-manager] couldn't check>
Jul 14 16:52:42 Art-ig ModemManager[869]: <info>  [base-manager] couldn't check>
Jul 14 16:52:45 Art-ig mgaapplet[6917]: trying distributions list from https://>
Jul 14 16:52:46 Art-ig ifplugd(enp2s0)[1355]: Executing '/etc/ifplugd/ifplugd.a>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Withdrawing address record for 2a02:6>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Leaving mDNS multicast group on inter>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Registering new address record for fe>
Jul 14 16:52:46 Art-ig postfix/postfix-script[52041]: refreshing the Postfix ma>
Jul 14 16:52:46 Art-ig postfix/master[6671]: reload -- version 3.5.9, configura>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Withdrawing address record for 192.16>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Leaving mDNS multicast group on inter>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Interface enp2s0.IPv4 no longer relev>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Interface enp2s0.IPv6 no longer relev>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Leaving mDNS multicast group on inter>
Jul 14 16:52:46 Art-ig avahi-daemon[874]: Withdrawing address record for fe80::>
Jul 14 16:52:46 Art-ig ifplugd(enp2s0)[1355]: client: Unknown parameter "-r". U>
Jul 14 16:52:46 Art-ig ifplugd(enp2s0)[1355]: client: run-parts: /etc/sysconfig>
Jul 14 16:52:46 Art-ig ifplugd(enp2s0)[1355]: Program executed successfully.
Jul 14 16:52:46 Art-ig kernel: Generic FE-GE Realtek PHY r8169-200:00: attached>
Jul 14 16:52:46 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Down
Jul 14 16:52:50 Art-ig kernel: r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/>
Jul 14 16:52:50 Art-ig kernel: IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link beco>
Jul 14 16:52:50 Art-ig mgaapplet[6917]: empty distribution list
Jul 14 16:52:50 Art-ig mgaapplet[6917]: Computing new updates...
Jul 14 16:52:50 Art-ig mgaapplet[6917]: Checking Network: seems disabled
Jul 14 16:52:50 Art-ig mgaapplet[6917]: running: mgaapplet-update-checker
Jul 14 16:52:50 Art-ig mgaapplet-update-checker[52119]: ### Program is starting>
Jul 14 16:52:50 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update ->
Jul 14 16:52:50 Art-ig pkexec[52123]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:50 Art-ig pkexec[52123]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:50 Art-ig ifplugd(enp2s0)[1355]: Link beat detected.
Jul 14 16:52:51 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 16:52:51 Art-ig avahi-daemon[874]: New relevant interface enp2s0.IPv6 fo>
Jul 14 16:52:51 Art-ig avahi-daemon[874]: Registering new address record for fe>
Jul 14 16:52:51 Art-ig mgaapplet-update-checker[52119]: updating inactive backp>
Jul 14 16:52:51 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update C>
Jul 14 16:52:51 Art-ig pkexec[52156]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:51 Art-ig pkexec[52156]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:51 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update N>
Jul 14 16:52:51 Art-ig pkexec[52721]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:51 Art-ig pkexec[52721]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:51 Art-ig ifplugd(enp2s0)[1355]: Executing '/etc/ifplugd/ifplugd.a>
Jul 14 16:52:52 Art-ig dhclient[53351]: DHCPREQUEST for 192.168.178.20 on enp2s>
Jul 14 16:52:52 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update T>
Jul 14 16:52:52 Art-ig pkexec[53682]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:52 Art-ig pkexec[53682]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:52 Art-ig dhclient[53351]: DHCPACK of 192.168.178.20 from 192.168.>
Jul 14 16:52:52 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 16:52:52 Art-ig avahi-daemon[874]: New relevant interface enp2s0.IPv4 fo>
Jul 14 16:52:52 Art-ig avahi-daemon[874]: Registering new address record for 19>
Jul 14 16:52:52 Art-ig postfix/postfix-script[54645]: refreshing the Postfix ma>
Jul 14 16:52:52 Art-ig postfix/master[6671]: reload -- version 3.5.9, configura>
Jul 14 16:52:52 Art-ig dhclient[53351]: bound to 192.168.178.20 -- renewal in 4>
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: client: Determining IP informatio>
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: client: INFO      : [/etc/sysconf>
Jul 14 16:52:52 Art-ig /etc/sysconfig/network-scripts/ifup-ipv6[55054]: Given I>
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: client: ERROR     : [/etc/sysconf>
Jul 14 16:52:52 Art-ig /etc/sysconfig/network-scripts/ifup-ipv6[55113]: 6to4 co>
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: client: Unknown parameter "-r". U>
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: client:  [  OK  ]
Jul 14 16:52:52 Art-ig ifplugd(enp2s0)[1355]: Program executed successfully.
Jul 14 16:52:53 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update C>
Jul 14 16:52:53 Art-ig pkexec[55176]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:53 Art-ig pkexec[55176]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:54 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update N>
Jul 14 16:52:54 Art-ig pkexec[55200]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:54 Art-ig pkexec[55200]: walter: Executing command [USER=root] [TT>
Jul 14 16:52:55 Art-ig mgaapplet-update-checker[52119]: running: urpmi.update T>
Jul 14 16:52:55 Art-ig pkexec[55209]: pam_unix(polkit-1:session): session opene>
Jul 14 16:52:55 Art-ig pkexec[55209]: walter: Executing command [USER=root] [TT>
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Recovering from system lockup, not al>
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:05 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:06 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:07 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:07 Art-ig rtkit-daemon[898]: Supervising 0 threads of 0 processes >
Jul 14 16:53:32 Art-ig mgaapplet[6917]: Packages are up to date
Jul 14 16:54:06 Art-ig at-spi-bus-launcher[14061]: dbus-daemon[14061]: Activati>
Jul 14 16:54:06 Art-ig at-spi-bus-launcher[14061]: dbus-daemon[14061]: Successf>
Jul 14 16:54:06 Art-ig at-spi-bus-launcher[63109]: SpiRegistry daemon is runnin>
Jul 14 16:54:11 Art-ig su[63143]: (to root) walter on pts/0
Jul 14 16:54:11 Art-ig su[63143]: pam_unix(su-l:session): session opened for us>
Jul 14 16:54:11 Art-ig dbus-daemon[875]: [system] Activating via systemd: servi>
Jul 14 16:54:11 Art-ig systemd[1]: Starting Hostname Service...
Jul 14 16:54:11 Art-ig dbus-daemon[875]: [system] Successfully activated servic>
Jul 14 16:54:11 Art-ig systemd[1]: Started Hostname Service.
Jul 14 16:54:41 Art-ig systemd[1]: systemd-hostnamed.service: Succeeded.
Jul 14 16:58:19 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 16:58:20 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 16:58:22 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 16:58:26 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:01:01 Art-ig CROND[113282]: (root) CMD (nice -n 19 run-parts --report>
Jul 14 17:01:01 Art-ig anacron[113287]: Anacron started on 2021-07-14
Jul 14 17:01:01 Art-ig anacron[113287]: Will run job `cron.daily' in 22 min.
Jul 14 17:01:01 Art-ig anacron[113287]: Will run job `cron.weekly' in 42 min.
Jul 14 17:01:01 Art-ig anacron[113287]: Jobs will be executed sequentially
Jul 14 17:01:18 Art-ig systemd[1]: Starting Cleanup of Temporary Directories...
Jul 14 17:01:18 Art-ig systemd[1]: systemd-tmpfiles-clean.service: Succeeded.
Jul 14 17:01:18 Art-ig systemd[1]: Finished Cleanup of Temporary Directories.
Jul 14 17:01:19 Art-ig avahi-daemon[874]: Leaving mDNS multicast group on inter>
Jul 14 17:01:19 Art-ig avahi-daemon[874]: Joining mDNS multicast group on inter>
Jul 14 17:01:19 Art-ig avahi-daemon[874]: Registering new address record for 2a>
Jul 14 17:01:19 Art-ig avahi-daemon[874]: Withdrawing address record for fe80::>
Jul 14 17:01:42 Art-ig su[118334]: (to root) walter on pts/1
Jul 14 17:01:42 Art-ig su[118334]: pam_unix(su-l:session): session opened for u>
Jul 14 17:01:42 Art-ig dbus-daemon[875]: [system] Activating via systemd: servi>
Jul 14 17:01:42 Art-ig systemd[1]: Starting Hostname Service...
Jul 14 17:01:42 Art-ig dbus-daemon[875]: [system] Successfully activated servic>
Jul 14 17:01:42 Art-ig systemd[1]: Started Hostname Service.
Jul 14 17:02:12 Art-ig systemd[1]: systemd-hostnamed.service: Succeeded.
Jul 14 17:03:50 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:03:51 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:03:53 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:03:57 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:03:59 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:04:00 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:04:02 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:04:06 Art-ig kernel: net-fw DROP IN=enp2s0 OUT= MAC=40:8d:5c:3e:57:c7>
Jul 14 17:06:40 Art-ig sensord[1069]: Chip: acpitz-acpi-0
Jul 14 17:06:40 Art-ig sensord[1069]: Adapter: ACPI interface
Jul 14 17:06:40 Art-ig sensord[1069]:   temp1: 27.8 C
Jul 14 17:06:40 Art-ig sensord[1069]:   temp2: 29.8 C
Jul 14 17:06:40 Art-ig sensord[1069]: Chip: coretemp-isa-0000
Jul 14 17:06:40 Art-ig sensord[1069]: Adapter: ISA adapter
Jul 14 17:06:40 Art-ig sensord[1069]:   Package id 0: 33.0 C
Jul 14 17:06:40 Art-ig sensord[1069]:   Core 0: 30.0 C
Jul 14 17:06:40 Art-ig sensord[1069]:   Core 1: 29.0 C
Jul 14 17:06:40 Art-ig sensord[1069]:   Core 2: 29.0 C
Jul 14 17:06:40 Art-ig sensord[1069]:   Core 3: 30.0 C
lines 1773-1795/1795 (END)

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 18:08
von man-draker
Ich hoffe, dass in den jetzt geposteten Logs genug Informationen sind, um zumindest Vergleiche anstellen zu können.
Ich habe allerdings seit Jahren keine entsprechenden Laufwerke mehr, so dass mir das nicht möglich ist.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 20:57
von ikseran
ja, das hoffe ich auch, ich habe da keine Ahnung. Kann es denn sein, dass ich da als einziger nach dem Update so eine Fehlfunktion habe!?

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 14th, '21, 22:20
von doktor5000
Anscheinend schon. Ich würde evtl. erstmal probieren das Laufwerk auszubauen und neu anzuschließen, evtl. hat es einen Wackelkontakt o.ä.

Ansonsten gibt es hier noch ein paar Anregungen: https://www.reddit.com/r/thinkpad/comme ... identally/

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 15th, '21, 08:29
von ikseran
Also, wechsle ich wieder zum vorigen Kernel (kernel-desktop-5.10.46-1), so bleibt das ungewollte Öffnen des DVD-Laufwerks aus dem Bereitschaftsmodus aus. Somit schließe ich einen Wackelkontakt definitv aus. Es hängt mit dem neuen Kernel (kernel-desktop-5.10.48-1) zusammen.
Es sieht für mich (aus laienhafter Sicht) so aus, dass das Laufwerk beim Herausgehen aus dem Bereitschaftsmodus (MATE) oder Standbymodus (Plasma) nicht nur initiiert wird, sondern zusätzlich einen "Befehl" zum Öffnen bekommt.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 15th, '21, 15:53
von doktor5000
Dann wird es sich vmtl. um folgende Änderung bei 5.10.48 handeln: https://git.kernel.org/pub/scm/linux/ke ... 524803c7f3

Wenn es bei dir reproduzierbar ist, dann kannst du das ja melden: https://bugs.mageia.org/

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 15th, '21, 17:20
von ikseran
habe es als Bug gemeldet.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 15th, '21, 17:30
von doktor5000
Ahh ja, und den Link zu dem Patch den ich gepostet habe wolltest du nicht noch mit hinzufügen, da soll der Entwickler dann vermutlich erst mal eine Runde raten was das Problem ist? :|

Habs mal in https://bugs.mageia.org/show_bug.cgi?id=29262 ergänzt.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 07:48
von ikseran
Du überforderst mich. Ich bin schon froh, wenn ich mich durch die Bugseite gewurschtelt habe. Und woher sollte ich das wissen, dass ich Deinen Link einfügen sollte?

Danke jedenfalls für die Ergänzung.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 14:33
von doktor5000
Der Entwickler sollte dann vermutlich erraten wie hier im Forum-Thread, warum der Fehler gerade bei dir auftritt ? Ohne jegliche Details zur verwendeten Hardware ...

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 15:28
von ikseran
Ein weiterer Vorwurf, aber wozu? Ich ging davon aus, dass nach Wechsel zum neuen Kernel bei mehreren Nutzern dieser Fehler auftreten würde, deswegen habe ich den Beitrag hier eingestellt. Nachdem Du mir geraten hast dies als Bug zu melden habe ich das getan. Über weitere innere Zusammenhänge weiß ich nicht Bescheid. Dass die verwendete Hardware nun auch wesentlich sein soll, erfahre ich nun von Dir ... zum ersten Mal.
Aber Hardware, in welchem Umfang?

Das DVD-Laufwerk ist: ‎ATAPI iHAS122 E
der SATA-Kontroller: 9 Series Chipset Family SATA Controller [AHCI Mode] von Intel Corporation
der SMBus-Controller: 9 Series Chipset Family SMBus Controller von Intel

Welche Hardware nun außerdem nötig ist, das weiß ich nicht, aber ich kann diese gerne hier anfügen, wenn es nötig ist.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 19:17
von doktor5000
ikseran hat geschrieben:Ein weiterer Vorwurf, aber wozu?

Um Verständnis zu schaffen. Wenn man einen Bug meldet, sollte der klar reproduzierbar. Wenn es sich auf Hardware bezieht, sollte _mindestens_ erwähnt werden, um welche Hardware es sich handelt.

ikseran hat geschrieben:Ich ging davon aus, dass nach Wechsel zum neuen Kernel bei mehreren Nutzern dieser Fehler auftreten würde, deswegen habe ich den Beitrag hier eingestellt.

Dann hätten es auch bereits mehrere Nutzer gemeldet, was allerdings nicht der Fall ist.

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 20:00
von ikseran
Wenn es sich auf Hardware bezieht


Die Bugmeldung bezieht sich auf den Kernel, so dachte ich zumindest. Ebenso ging ich davon aus, dass meine Bugmeldung abgesehen von vlt. sprachlichen Fehlern korrekt sei. Einen Anlass, Hardware mitzuteilen konnte ich aufgrund der Bugseite nicht ersehen.

Dann hätten es auch bereits mehrere Nutzer gemeldet, was allerdings nicht der Fall ist
Wie sollte ich das voraussehen?

Um Verständnis zu schaffen
schaffen Vorwürfe wirklich Verständnis? Sie schaffen schlechte Laune oder zeigen die schlechte Laune des Vorwerfenden.

Manchmal habe ich das Gefühl, dass jemand, der sich so intensiv in der Materie befindet, nicht mehr verstehen kann, dass es auch Menschen gibt, die nicht diesen Durchblick haben. All diese Zusammenhänge, die Du natürlich sofort siehst, die gibt es für mich nicht. Um Übrigen würde es Dir vermutlich auch so gehen, wenn ich von Dir erwarten würde, mir spontan die Cis-Klappe am Saxophon zu zeigen oder die Oktavklappe (vorausgesetzt, Du spielst nicht Saxophon).

Re: CD-Laufwerk öffnet sich ungewollt

BeitragVerfasst: Jul 16th, '21, 23:07
von doktor5000
Um das mal zu vergleichen, du würdest dann vermutlich bei einem Problem mit deinem Auto bei der Werkstatt anrufen, und das so beschreiben:
"Ja da geht das Handschuhfach immer auf wenn ich die Zündung anmache" mit der Erwartungshaltung dass die eine Ferndiagnose machen und das aus der Ferne reparieren, ohne dass die das Auto mal gesehen haben oder weitere Details?
Auch ohne jegliches Technikverständnis - sagt da nicht schon der gesunde Menschenverstand, dass das vielleicht eine geringfügig unrealistische Erwartungshaltung wäre ?

Noch als kleiner Nachtrag, die Anleitung, wie ein Bug zu melden ist, findet man im Wiki - da wird das ganz gut beschrieben worauf es ankommt: https://wiki.mageia.org/en/Wie_ein_Fehl ... et_wird-de
Dort steht auch drin, dass man schauen sollte, ob der Fehler bereits gemeldet wurde.
Alle Zeiten sind UTC + 1 Stunde
Seite 1 von 2
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/