man-draker hat geschrieben:Dir ist schon aufgefallen, dass "scanimage -L" nur die Webcam listet und nicht den Lide?
Ja, das ist schon richtig, aber erst beim zweiten Mal. Ich habe den Befehl nun zwei mal ausgeführt, nachdem ich den Scanner neu angesteckt hatte. Und siehe da: erstes Mal erkannt, zweites Mal nicht.
- Code: Alles auswählen
[root@localhost dev]# scanimage -L
device `plustek:libusb:003:060' is a Canon CanoScan N670U/N676U/LiDE20 flatbed scanner
[root@localhost dev]# scanimage -L
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
man-draker hat geschrieben:Außerdem wurde der Scanner zwar als Gerät am USB-Bus gefunden, aber nicht als Scanner identifiziert. Andernfalls wäre das gemeldet worden:
- Code: Alles auswählen
{device `plustek:libusb:003:054' is a Canon CanoScan N670U/N676U/LiDE20 flatbed scanner}
Ah, ok, ist auch dieses Mal wieder nicht der Fall. Es könnte allerdings schon in der gezeigten Art und Weise geschehen sein.
man-draker hat geschrieben:Wie sehen die anzupassenden Einträge in deiner /etc/sane.d/plustek.conf aus?
Da ich nicht weiß, welche Einträge du meinst, hänge ich die ganze Datei an. Ich versteh das nicht, der speichert manche oder zeitweise die Dateien nicht. -Ah, *.conf ist als Anhang nicht erlaubt. Nun eben doch als Code. Ich hatte es auch schon mit der alternativ Variante probiert, was nichts änderte.
- Code: Alles auswählen
# Plustek-SANE Backend configuration file
# For use with LM9831/2/3 based USB scanners
#
# each device needs at least two lines:
# - [usb] vendor-ID and product-ID
# - device devicename
# i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)
# [usb] 0x07B3 0x0017
# device /dev/usbscanner
# or
# device libusb:bbb:ddd
# where bbb is the busnumber and ddd the device number
# make sure that your user has access to /proc/bus/usb/bbb/ddd
#
# additionally you can specify some options
# warmup, lOffOnEnd, lampOff
#
# For autodetection use
# [usb]
# device /dev/usbscanner
#
# or simply
# [usb]
#
# or if you want a specific device but you have no idea about the
# device node or you use libusb, simply set vendor- and product-ID
# [usb] 0x07B3 0x0017
# device auto
#
# NOTE: autodetection is safe, as it uses the info it got
# from the USB subsystem. If you're not using the
# autodetection, you MUST have attached that device
# at your USB-port, that you have specified...
#
[usb] alternativ: [usb] 0x04a9 0x220d
#
# options for the previous USB entry
#
# switch lamp off after xxx secs, 0 disables the feature
# (can also be set via frontend)
option lampOff 300
# warmup period in seconds, 0 means no warmup, -1 means auto-warmup
# (can also be set via frontend)
option warmup -1
# 0 means leave lamp-status untouched, not 0 means switch off
# on sane_close
# (can also be set via frontend)
option lOffOnEnd 1
#
# options to tweak the image start-position
# (WARNING: there's no internal range check!!!)
#
# for the normal scan area
#
option posOffX 0
option posOffY 0
# for transparencies
option tpaOffX 0
option tpaOffY 0
# for negatives
option negOffX 0
option negOffY 0
#
# for setting the calibration strip position
# (WARNING: there's no internal range check!!!)
# -1 means use built in
# (can also be set via frontend)
option posShadingY -1
option tpaShadingY -1
option negShadingY -1
#
# to invert the negatives, 0 disables the feature
#
option invertNegatives 0
#
# to disable the internal sensor speedup function,
# 1 disables the feature
#
option disableSpeedup 0
#
# to save/restore coarse calibration data
# (can also be set via frontend)
option cacheCalData 0
#
# use alternate calibration routines
#
option altCalibration 0
#
# for skipping whole calibration step
#
option skipCalibration 0
#
# for skipping entire fine calibration step
# coarse calibration is done
#
option skipFine 0
#
# discard the result of the fine white calibration
#
option skipFineWhite 0
#
# some scanners have a dark calibration strip, in
# general this one should be used for calibration.
# As this could cause some trouble, this option
# overrides that and the dark calibration will be
# done by switching the lamp off
#
option skipDarkStrip 0
# for replacing the gain values found during coarse
# calibration
# (can also be set via frontend)
option red_gain -1
option green_gain -1
option blue_gain -1
# for replacing the offset values found during coarse
# calibration
# (can also be set via frontend)
option red_offset -1
option green_offset -1
option blue_offset -1
#
# for replacing the default lampoff settings, this
# works only for CIS devices like CanoScan LiDE20
# (can also be set via frontend)
option red_lampoff -1
option green_lampoff -1
option blue_lampoff -1
#
# for adjusting the default gamma values
# (can also be set via frontend)
option redGamma 1.0
option greenGamma 1.0
option blueGamma 1.0
option grayGamma 1.0
#
# to enable TPA (EPSON or UMAX, if autodetection fails)
# 0 means default behaviour as specified in the internal tables
# 1 means enable (needed for UMAX 3450)
option enableTPA 0
#
# model override functionality, currently only available for
# Mustek devices, using NSCs' vendor ID: 0x0400 and
# also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)
#
# mov/PID | 0x1000 | 0x1001
# ---------------------------------------
# 0 (default)| BearPaw1200 | BearPaw 2400
# 1 | ignored | BearPaw 1200
#
option mov 0
#
# and of course the device-name
#
# device /dev/usbscanner
device auto
#
# to define a new device, start with a new section:
# [usb]
#
man-draker hat geschrieben:Und wird das Gerät immer noch unter "003:054" gefunden?
Nein, der zählt, wie du sagtest weiter hoch. Inzwischen bin ich in den Sechzigern: 003:06x . Das dürfte also passen.
jkowalzik hat geschrieben:Unter Linux müssen Sie Libusb Geräteschutz einzurichten .
und man kommt auf die Seite:https://translate.googleusercontent.com/translate_c?depth=1&hl=de&prev=search&rurl=translate.google.de&sl=en&u=http://www.freecolormanagement.com/sane/libusb.html&usg=ALkJrhi0ujQyBQu9iJ-o8BdCDUTsMSdWIg...das ist aber nur ein Strohhalm als Angebot
Danke für den Strohhalm J. Ich werde mir das noch mal ansehen und schauen, ob sich daraus was ergibt. Fakt ist jedenfalls, dass Sane den Canon Lide 20 vollständig unterstützt. Somit muss es ja möglich sein ihn zum Laufen bzw. Scannen zu bringen, in der Art, wie es ihm angedacht ist.